Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Dec 12, 2024 8:05 am


All times are UTC - 5 hours


Forum rules


Be nice, no cussin and enjoy!




Post new topic Reply to topic  [ 36 posts ]  Go to page Previous  1, 2
Author Message
PostPosted: Mon Jan 22, 2018 10:15 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Apr 16, 2012 12:47 pm
Posts: 2524
First name: Jay
Last Name: De Rocher
City: Bothell
State: Washington
Do you need a description of how to do the test?

_________________
Once in a while you get shown the light in the strangest of places if you look at it right - Robert Hunter



These users thanked the author J De Rocher for the post: bcombs510 (Mon Jan 22, 2018 10:17 pm)
Top
 Profile  
 
PostPosted: Mon Jan 22, 2018 10:19 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Mon Jul 27, 2015 8:21 am
Posts: 3613
First name: Brad
Last Name: Combs
Focus: Build
Status: Amateur
What I read in some random site last night:

1) Put a small amount of the potassium carbonate in a small container. The site showed a lid to a 20 oz bottle half way full.

2) Put a small amount of water in the cap. Just enough to wet it.

3) Put the cap and the hygrometer in a gallon ziplock overnight.

If the hygrometer shows 45% humidity then it is accurate. If not, calibrate accordingly.

Is that how you test?


Sent from my iPhone using Tapatalk

_________________
Insta - https://www.instagram.com/cbcguitars/
Facebook - https://www.facebook.com/cbcguitars


Top
 Profile  
 
PostPosted: Mon Jan 22, 2018 10:40 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Apr 16, 2012 12:47 pm
Posts: 2524
First name: Jay
Last Name: De Rocher
City: Bothell
State: Washington
Basically, yes. From what I read from a few different sources though, the RH for equilibration with potassium carbonate is at 43%.

I use a transparent tupperware type container (about 5" w x 9" l x 2" h) with a lid with a gasket and put the salt in a small ceramic dish (appropriated from the kitchen). You also need to use distilled water since salts in tap water could throw off the measurement. I let it sit closed for 24 hours. The amount of potassium carbonate you describe sounds similar to what I use in my tupperware container.

The way I do it is based on this post on the Australian/New Zealand Luthiers Forum (first post): http://www.anzlf.com/viewtopic.php?t=6123

_________________
Once in a while you get shown the light in the strangest of places if you look at it right - Robert Hunter



These users thanked the author J De Rocher for the post: bcombs510 (Mon Jan 22, 2018 11:16 pm)
Top
 Profile  
 
PostPosted: Mon Jan 22, 2018 11:16 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Mon Jul 27, 2015 8:21 am
Posts: 3613
First name: Brad
Last Name: Combs
Focus: Build
Status: Amateur
Perfect. Thanks!


Sent from my iPhone using Tapatalk

_________________
Insta - https://www.instagram.com/cbcguitars/
Facebook - https://www.facebook.com/cbcguitars


Top
 Profile  
 
PostPosted: Tue Jan 23, 2018 8:57 am 
Offline
Koa
Koa
User avatar

Joined: Wed Jan 14, 2009 3:14 am
Posts: 992
Location: Shefford, Québec
First name: Tim
Last Name: Mullin
City: Shefford
State: QC
Zip/Postal Code: J2M 1R5
Country: Canada
Focus: Build
Status: Professional
Mechanical hygrometers can easily be knocked out of calibration — can’t imagine Amazon shipping being delicate. Calibrate ALL hygrometers with K2CO3 on arrival and repeat annually. Photo shows a couple of my digital humidor hygrometers and the sensor for my wood-room humidity control system in a sealed plastic box with a dish of K2CO3, dampened with distilled water. They stay there overnight for adjustment the next day. (Humidity controller manages a humidifier and a dehumidifier on separate channels).
Image

Sent from my iPad using Tapatalk



These users thanked the author Tim Mullin for the post: bcombs510 (Tue Jan 23, 2018 10:50 am)
Top
 Profile  
 
PostPosted: Thu Jan 25, 2018 8:43 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Mon Jul 27, 2015 8:21 am
Posts: 3613
First name: Brad
Last Name: Combs
Focus: Build
Status: Amateur
Testing is underway with the replacement from Amazon. Interestingly the RH spiked right away. I’m guessing it takes a while to stabilize and will come back down to the expected 43%?

Image


Sent from my iPhone using Tapatalk

_________________
Insta - https://www.instagram.com/cbcguitars/
Facebook - https://www.facebook.com/cbcguitars



These users thanked the author bcombs510 for the post: Bryan Bear (Fri Jan 26, 2018 8:54 am)
Top
 Profile  
 
PostPosted: Thu Jan 25, 2018 8:52 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Apr 16, 2012 12:47 pm
Posts: 2524
First name: Jay
Last Name: De Rocher
City: Bothell
State: Washington
That replacement is looking much better right off the bat. Yes, it takes a while to equilibrate in there. Overnight at least depending on the starting RH value.

_________________
Once in a while you get shown the light in the strangest of places if you look at it right - Robert Hunter



These users thanked the author J De Rocher for the post: bcombs510 (Thu Jan 25, 2018 8:52 pm)
Top
 Profile  
 
PostPosted: Fri Jan 26, 2018 4:45 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Mon Jul 27, 2015 8:21 am
Posts: 3613
First name: Brad
Last Name: Combs
Focus: Build
Status: Amateur
J De Rocher wrote:
That replacement is looking much better right off the bat. Yes, it takes a while to equilibrate in there. Overnight at least depending on the starting RH value.


Here it is after about 19 hours. The salt was rock hard when I opened the lid. Is that expected or did I not add enough distilled water to the mix?

Image

Brad


Sent from my iPhone using Tapatalk

_________________
Insta - https://www.instagram.com/cbcguitars/
Facebook - https://www.facebook.com/cbcguitars


Top
 Profile  
 
PostPosted: Fri Jan 26, 2018 5:21 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Apr 16, 2012 12:47 pm
Posts: 2524
First name: Jay
Last Name: De Rocher
City: Bothell
State: Washington
Probably not enough water. The potassium carbonate should still look wet and not be a hard rock.

I looked it up and found that a "saturated solution" of potassium carbonate can be made with a ratio of 1 ml of water per 2.2 grams of potassium carbonate. That's what you want to aim for. I'm guessing there's leeway around that ratio since none of the methods I've read call for exact measurements. You just don't want to add so much water that there is free standing water in the salts.

_________________
Once in a while you get shown the light in the strangest of places if you look at it right - Robert Hunter



These users thanked the author J De Rocher for the post: bcombs510 (Fri Jan 26, 2018 7:38 pm)
Top
 Profile  
 
PostPosted: Fri Jan 26, 2018 7:38 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Mon Jul 27, 2015 8:21 am
Posts: 3613
First name: Brad
Last Name: Combs
Focus: Build
Status: Amateur
J De Rocher wrote:
Probably not enough water. The potassium carbonate should still look wet and not be a hard rock.

I looked it up and found that a "saturated solution" of potassium carbonate can be made with a ratio of 1 ml of water per 2.2 grams of potassium carbonate. That's what you want to aim for. I'm guessing there's leeway around that ratio since none of the methods I've read call for exact measurements. You just don't want to add so much water that there is free standing water in the salts.


Thanks, Jay. I’ll give it a try again tonight.

Brad


Sent from my iPhone using Tapatalk

_________________
Insta - https://www.instagram.com/cbcguitars/
Facebook - https://www.facebook.com/cbcguitars


Top
 Profile  
 
PostPosted: Sat Jan 27, 2018 7:52 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Mon Jul 27, 2015 8:21 am
Posts: 3613
First name: Brad
Last Name: Combs
Focus: Build
Status: Amateur
Image

43, 43, 44, and 44.... Looks like the new digitals are dead on and the old digital and new mechanical are +1.

I think we are good to go! Appreciate the help, Jay!


Sent from my iPhone using Tapatalk

_________________
Insta - https://www.instagram.com/cbcguitars/
Facebook - https://www.facebook.com/cbcguitars



These users thanked the author bcombs510 for the post (total 2): J De Rocher (Sun Jan 28, 2018 2:15 am) • Bryan Bear (Sat Jan 27, 2018 7:59 pm)
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 36 posts ]  Go to page Previous  1, 2

All times are UTC - 5 hours


Who is online

Users browsing this forum: Ken Nagy, Tom G and 25 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com