Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Dec 12, 2024 11:05 am


All times are UTC - 5 hours


Forum rules


Be nice, no cussin and enjoy!




Post new topic Reply to topic  [ 62 posts ]  Go to page Previous  1, 2, 3
Author Message
PostPosted: Sat Nov 04, 2017 9:38 am 
Offline
Cocobolo
Cocobolo

Joined: Sat Dec 28, 2013 10:06 am
Posts: 256
First name: Mike
Last Name: Spector
City: ORANGE
State: TX
Zip/Postal Code: 77632
Country: USA
Focus: Build
Status: Amateur
For a comparison, take 2 assembled x-braces, (1) standard notch and (1) with the "arch" notch and set them both on 4 blocks each. Start adding weight in increments of --- until one breaks. The arched one will surely break first if built the way you show it. Then build another "arch" notch x-brace with each notch being at the outside of a knothole with the knot removed on each leg of the brace where the grain will swirl around the "arch" and compare that to the standard square notch type of x-brace with the same weights. You could probably use 1 x 2's shaped down and do it on a larger scale for ease of getting the grain like you want it on the "arch" notch.


Top
 Profile  
 
PostPosted: Sat Nov 04, 2017 10:31 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Thu Feb 12, 2009 12:12 pm
Posts: 3293
First name: Bryan
Last Name: Bear
City: St. Louis
State: Mo
Country: USA
Focus: Build
Status: Amateur
surveyor wrote:
For a comparison, take 2 assembled x-braces, (1) standard notch and (1) with the "arch" notch and set them both on 4 blocks each. Start adding weight in increments of --- until one breaks. The arched one will surely break first if built the way you show it. Then build another "arch" notch x-brace with each notch being at the outside of a knothole with the knot removed on each leg of the brace where the grain will swirl around the "arch" and compare that to the standard square notch type of x-brace with the same weights. You could probably use 1 x 2's shaped down and do it on a larger scale for ease of getting the grain like you want it on the "arch" notch.


I don’t think it is as sure as you think that the arched brace will break first in the test you propose. The point Wud is making is that the squared corner of the notch concentrates all the stress right at a grain line along the weakest plane of the wood (which is why we split bracewood to make that weak plane as long as possible inside the brace). The arched notch will spread that force out over a larger area and of end grain. I’m not saying the square notch will break first, just that you can’t assume it won’t.

The problem with designing these tests, and what I was trying to get at in an earlier post is that you have to design a test that simulates the real world forces and seeks to answer a relevant question. In the test you propose, the forces are not similar to the forces the joint will see in use. On a guitar, one side of the joint is completely glued to a spruce top closing the bottom notch. The top notch can be closed in several ways too. The force on this joint is pulling across the top and rotating a bridge down behind the joint and pulling the fretboard extension down in front of the sound hole. The boundaries of the top are not free and have a waist close to part of the joint further complicating the stiffness of the plate. All of that would have to be designed into the experiment.

Then there is the matter of what question are you answering. This test would show which joint would break first if you sat on the guitar top. IMHO, that is not a relevant test. Any joint would fail at some point under a load that the guitar is not intended to handle. Do we care which one would fail first. I suppose so, if one were so weak that somewhat rough handling would lead to failure but I suspect either would hold up to reasonable bumps.

_________________
Bryan Bear PMoMC

Take care of your feet, and your feet will take care of you.


Top
 Profile  
 
PostPosted: Sat Nov 04, 2017 3:07 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Jul 27, 2009 7:52 am
Posts: 4524
First name: Big
Last Name: Jim
State: Deep in the heart of Bluegrass
Country: usa
Focus: Build
Status: Amateur
[/quote]The point Wud is making is that the squared corner of the notch concentrates all the stress right at a grain line along the weakest plane of the wood (which is why we split bracewood to make that weak plane as long as possible inside the brace). The arched notch will spread that force out over a larger area and of end grain. I’m not saying the square notch will break first, just that you can’t assume it won’t.[/quote]


Exactly Bryan. The lower arch is connected all the way across and will be capped across the upper . It is an assumption to state either will fail first . Too many variables involved. Each case could be different, however in time the % would start to tell the story.

_________________
The Shallower the depth of the stream , The Louder the Babble !
The Taking Of Offense Is the Life Course Of The Stupid One !
Wanna Leave a Better Planet for our Kids? How about Working on BETTER KIDS for our Planet !
Forgiveness is the ability to accept an apology that you will probably NEVER GET
The truth will set you free , But FIRST, it will probably Piss you Off !
Creativity is allowing yourself to make Mistakes, Art is knowing which ones to Keep !
The Saddest thing anyone can do , is push a Loyal Person to the point that they Dont Care Anymore
Never met a STRONG person who had an EASY past !
http://wiksnwudwerks.blogspot.com/
http://www.facebook.com/groups/GatewayA ... rAssembly/


Top
 Profile  
 
PostPosted: Sat Nov 04, 2017 5:57 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Thu Feb 12, 2009 10:27 pm
Posts: 2109
Location: South Carolina
First name: John
Last Name: Cox
Focus: Build
Status: Amateur
Jim - If you really want to try this out for the sake of trying it - go ahead. You can't bake a cake without breaking some eggs. And often you learn a lot of interesting things by just trying it out to see what happens..

That said. I am going to put on my Grumpy Uncle John hat.....

This seems to be a solution in search of a problem....

Millions of X-braced guitars are made every year. X-braced guitars have been made for the better part of 150 years. Failure of the main X-joint is not a common failure by any means - even when the X is not capped at all... I have handled a bunch of guitars - including a bunch of broken ones... So far I have run across zero with a broken X at the joint.... I won't say it doesn't happen because I have seen pictures.... But I don't think anybody has it on their "common repairs" list....

So... If you are looking for a bona-fide structural deficiency with the current design - this isn't one.

If you just want to try it out - have at it.



These users thanked the author truckjohn for the post: Bryan Bear (Sat Nov 04, 2017 6:22 pm)
Top
 Profile  
 
PostPosted: Sat Nov 04, 2017 7:07 pm 
Offline
Koa
Koa
User avatar

Joined: Tue Nov 11, 2008 9:13 pm
Posts: 834
Location: Durango CO
First name: Dave
Last Name: Farmer
City: Durango
State: CO
truckjohn wrote:
..

This seems to be a solution in search of a problem....

Millions of X-braced guitars are made every year. X-braced guitars have been made for the better part of 150 years. Failure of the main X-joint is not a common failure by any means - even when the X is not capped at all... I have handled a bunch of guitars - including a bunch of broken ones... So far I have run across zero with a broken X at the joint.... I won't say it doesn't happen because I have seen pictures.... But I don't think anybody has it on their "common repairs" list....


Jeez John, now you've got me feeling self conscious about my clientele. Bunch a ruffians I guess. :? :)
I would say I'm a very low volume one man shop.
you've seen none?


Crappy laminated guitar and a D-28

Attachment:
WIN_20161013_12_02_34_Pro.jpg





Attachment:
WIN_20160430_104423.JPG


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
PostPosted: Sun Nov 05, 2017 2:56 pm 
Offline
Mahogany
Mahogany

Joined: Mon Sep 17, 2007 12:00 pm
Posts: 60
Location: Australia
What about butted X braces (no notch)?
Anyone see failures there? By separation from the soundboard?


Top
 Profile  
 
PostPosted: Sun Nov 05, 2017 4:12 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Thu Feb 12, 2009 10:27 pm
Posts: 2109
Location: South Carolina
First name: John
Last Name: Cox
Focus: Build
Status: Amateur
david farmer wrote:
Jeez John, now you've got me feeling self conscious about my clientele. Bunch a ruffians I guess. :? :)
I would say I'm a very low volume one man shop.
you've seen none?

Crappy laminated guitar and a D-28


That D-28 took a substantial top hit... Did somebody sit on it? Kids practicing kung fu? Its not often you see crossgrain top splits at the finger braces.

All I can say is that guitars aren't furniture - guitars are fragile by nature. If your clients need one for a bat - there are plastic ukulele's out there... ;) ;)



These users thanked the author truckjohn for the post: Bryan Bear (Sun Nov 05, 2017 5:04 pm)
Top
 Profile  
 
PostPosted: Sun Nov 05, 2017 5:06 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Fri Aug 19, 2005 4:02 am
Posts: 3264
Location: The Woodlands, Texas
First name: Barry
Last Name: Daniels
jeffhigh wrote:
What about butted X braces (no notch)?


Is this a thing?


Top
 Profile  
 
PostPosted: Sun Nov 05, 2017 5:10 pm 
Offline
Koa
Koa

Joined: Mon Jul 11, 2005 5:17 am
Posts: 1011
Location: United States
City: Tyler
State: Texas
jeffhigh wrote:
What about butted X braces (no notch)?
Anyone see failures there? By separation from the soundboard?


Gibson has already tried it.


Top
 Profile  
 
PostPosted: Sun Nov 05, 2017 5:19 pm 
Offline
Mahogany
Mahogany

Joined: Mon Sep 17, 2007 12:00 pm
Posts: 60
Location: Australia
Yes I know Gibson has used it, wondering what results have been seen by repairers.


Top
 Profile  
 
PostPosted: Tue Nov 14, 2017 10:04 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Jul 27, 2009 7:52 am
Posts: 4524
First name: Big
Last Name: Jim
State: Deep in the heart of Bluegrass
Country: usa
Focus: Build
Status: Amateur
Braces are .750 high and .3125 thick with the Cap it is .875 at X

Attachment:
Arch Brace1.jpg
Attachment:
arch brace2.jpg


You do not have the required permissions to view the files attached to this post.

_________________
The Shallower the depth of the stream , The Louder the Babble !
The Taking Of Offense Is the Life Course Of The Stupid One !
Wanna Leave a Better Planet for our Kids? How about Working on BETTER KIDS for our Planet !
Forgiveness is the ability to accept an apology that you will probably NEVER GET
The truth will set you free , But FIRST, it will probably Piss you Off !
Creativity is allowing yourself to make Mistakes, Art is knowing which ones to Keep !
The Saddest thing anyone can do , is push a Loyal Person to the point that they Dont Care Anymore
Never met a STRONG person who had an EASY past !
http://wiksnwudwerks.blogspot.com/
http://www.facebook.com/groups/GatewayA ... rAssembly/


Top
 Profile  
 
PostPosted: Tue Nov 14, 2017 11:06 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Wed Apr 08, 2009 9:34 am
Posts: 3081
Glad I used laminated bracing all these years...

Image


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 62 posts ]  Go to page Previous  1, 2, 3

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 27 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com