Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Wed Nov 27, 2024 3:42 pm


All times are UTC - 5 hours





Post new topic Reply to topic  [ 16 posts ] 
Author Message
PostPosted: Fri Feb 25, 2011 11:00 am 
Offline
Mahogany
Mahogany
User avatar

Joined: Wed Jan 26, 2011 3:18 pm
Posts: 46
First name: jeff
Last Name: scott
City: sasint john
State: new brusnwick
Zip/Postal Code: e2e 2e2
Country: Canada
Focus: Build
Status: Amateur
I have been watching many youtube video on scarf joints (headstock) and it seems most luthiers favour the band saw for cutting this.

PROBLEM 1: I built a 15 degree jig, but absolutely cannot get the band saw to bite the wood. I made a little starting groove at a wider angle, but at 15 degrees the blade always bends. Another teacher here (high school) said this it is possible the blade is not wide enough. It is a 1/4" blade. Has anyone been able to cut a 15 degree headstock with a 1/4" band saw blade?

PROBLEM 2: I have also built a jig for the table saw. Some test pieces cut nicely, and some were butchered. I hate to put my maple in there. Anyone cut this on a table saw with success?

PROBLEM 3: One of the best cuts I made was with a mitre saw. I set the blade at 15 degrees and just held the test wood perpendicular to the back fence. Not very accurate, but the best cut so far. Anyone been able to do this?


Top
 Profile  
 
PostPosted: Fri Feb 25, 2011 11:18 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sat Nov 26, 2005 7:32 pm
Posts: 1969
Location: United States
I use the table saw. You can mess up your neck easily. To avoid that, try a thin kerfed Diablo blade that is sharp. Be sure that your neck is firmly clamped to the sled - both behind and in front of the cut. Make sure your sled has very little play in it. Turn the saw off as soon as you go through the neck.

_________________
"An adventure is only an inconvenience rightly considered. An inconvenience is an adventure wrongly considered." G. K. Chesterton.


Top
 Profile  
 
PostPosted: Fri Feb 25, 2011 11:47 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sat May 17, 2008 1:11 pm
Posts: 2375
Location: Spokane, Washington
First name: Pat
Last Name: Foster
Country: USA
Focus: Build
If you have a table saw, you can try this jig. Works very well. Kathy Matsushita's site has a some pics and a plan.

http://home.comcast.net/~kathymatsushita/amateurluthier/htmlpages/scarfjig.html

Pat

_________________
formerly known around here as burbank
_________________

http://www.patfosterguitars.com


Top
 Profile  
 
PostPosted: Fri Feb 25, 2011 1:39 pm 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Wed Jan 14, 2009 10:11 pm
Posts: 352
Location: muncie IN
First name: shad
Last Name: peters
Focus: Build
a 1/4 blade is not going to want to do the job very much, especially if it is a fine tooth blade. if you can get a 3/8 or half inch blade with a fairly low tooth count it will help. 1/4 inch blade could probably do it as well if its in the neighborhood of 6tpi and sharp. if you are using a fine tooth blade it might tend to bind up once you get the cut started anyway.

_________________
~shad peters

http://www.flickr.com/photos/petersinstruments/
http://petersinstruments.blogspot.com/
http://petersinstruments.com/


Top
 Profile  
 
PostPosted: Mon Feb 28, 2011 9:21 pm 
Offline
Mahogany
Mahogany
User avatar

Joined: Wed Jan 26, 2011 3:18 pm
Posts: 46
First name: jeff
Last Name: scott
City: sasint john
State: new brusnwick
Zip/Postal Code: e2e 2e2
Country: Canada
Focus: Build
Status: Amateur
All good advice, especially about the guides on the band saw. Thanks.

I have built that same jig for the table saw. As I say, some cut well, others get chewed up. I guess I will have to try a few more practice cuts and then try the maple.


Top
 Profile  
 
PostPosted: Mon Feb 28, 2011 9:38 pm 
Offline
Koa
Koa
User avatar

Joined: Wed Jan 24, 2007 2:45 pm
Posts: 1336
Location: Calgary, Canada
Status: Amateur
A good Western or Japanese handsaw and a block plane work very good as well.


Top
 Profile  
 
PostPosted: Tue Mar 01, 2011 12:46 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Thu May 12, 2005 5:46 am
Posts: 2968
Location: United States
A bandsaw and then I clean it up with a hand plane.

_________________
Jim Watts
http://jameswattsguitars.com


Top
 Profile  
 
PostPosted: Wed Mar 02, 2011 5:22 am 
Offline
Mahogany
Mahogany
User avatar

Joined: Wed Jan 26, 2011 3:18 pm
Posts: 46
First name: jeff
Last Name: scott
City: sasint john
State: new brusnwick
Zip/Postal Code: e2e 2e2
Country: Canada
Focus: Build
Status: Amateur
I cut my first headstock with the mitre saw. It took a bit of rigging to get the wood perpendicular to the back fence, but it worked. The cut wasn't perfect, so I ran both pieces through the bench sander. Looked pretty good and I glued it yesterday, so this morning I will un-clamp it and check it out. Probably glue on the headstock wings to widen the surface area.


Top
 Profile  
 
PostPosted: Wed Mar 02, 2011 8:57 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri Jan 22, 2010 9:59 pm
Posts: 3595
First name: Dennis
Last Name: Kincheloe
City: Kansas City
State: MO
Country: USA
Focus: Build
Status: Amateur
I'm with Darrel. Mark a 15 degree line and go at it freehand. Still a little tricky to get started, but once you've got a notch to ride in, it's just a matter of keeping it vertical for a few minutes of cutting. Practice on a couple scraps and it gets pretty easy. I use one of these http://www.amazon.com/Tajima-PUL-265-Rapid-Pull-Blade/dp/B0008MGHUM/ref=sr_1_4?ie=UTF8&s=hi&qid=1299073451&sr=8-4. Excellent saw, far better than its price would suggest.


Top
 Profile  
 
PostPosted: Tue Apr 19, 2011 1:40 am 
Offline
Walnut
Walnut

Joined: Mon Dec 13, 2010 1:58 am
Posts: 8
First name: Eugene
Last Name: Parnell
City: Seattle
State: WA
Zip/Postal Code: 98107
Country: United States
Focus: Build
Status: Amateur
I have gone through all the same attempts. First I tried making a jig for a miter saw, and it didn't work too well. I tried once with a bandsaw and the amount of cleanup necessary with the plane afterward was too much. Finally I ended up making a jig for my table saw similar to (but not as nice as) the one on Kathy's site (linked above). I've had the best luck with that, although it sometimes comes out a bit out of square.

I'd also second the comment about a good *sharp* handsaw being just fine for the task. The junk saws you get at your local big-box home store aren't going to work too well. A nice Japanese handsaw takes some practice to use, but the blade and its kerf are so much thinner, it cuts surprisingly fast and clean.


Top
 Profile  
 
PostPosted: Tue Apr 19, 2011 7:48 am 
Offline
Koa
Koa

Joined: Sun Oct 28, 2007 4:40 pm
Posts: 763
Location: United States
I used the bandsaw at school. Awesome. Tried at home. Terrible. Used a handsaw. Frustrated. Upgraded bandsaw. Worked better. Regardless of your plan, you will still need to fine fit it with a plane. I also use a granite sanding block. (scrap from a counter guy) For my most recent, I'm doing a multi-scale which requires a compound angle for the scarf joint. On the advice of Mark Mustapick, I went back to the table saw. It was a revelation to me that my jigs and sled didn't need to go under the wood. I can't take credit for it. Saw a picture online somewhere, but don't remember where.

You do want to be very thoughtful of your clamp placement. And don't run your tablesaw with all that stuff on it. Just set it up for the photo.

Mike


You do not have the required permissions to view the files attached to this post.

_________________
Mike Lindstrom


Top
 Profile  
 
PostPosted: Tue Apr 19, 2011 1:08 pm 
Offline
Contributing Member
Contributing Member

Joined: Wed Apr 23, 2008 7:16 pm
Posts: 146
Here's the jig I use. It's just a few scraps of plywood. If your saw is well tuned and you have a good blade, you won't need to do any cleanup work.

Image

And, yeah, you don't want to cut through any clamps!

Joe


Top
 Profile  
 
PostPosted: Tue Apr 19, 2011 5:56 pm 
Offline
Koa
Koa

Joined: Sun Oct 28, 2007 4:40 pm
Posts: 763
Location: United States
Yeah, Joe. That's what I was trying to show. You took a much better picture.

Mike

_________________
Mike Lindstrom


Top
 Profile  
 
PostPosted: Tue Apr 19, 2011 8:21 pm 
Offline
Koa
Koa

Joined: Tue Apr 27, 2010 9:07 pm
Posts: 512
City: Tucson
State: AZ
Country: USA
Focus: Build
Status: Amateur
Draw angle out on neck blank, giving plenty of meat on either side of the cut. Set up your bandsaw, making sure your table is perpendicular to the blade, your blade is tight, your guides are set up close enough to the blade, and that the bearings are set up properly. Cut along the line sloooooooooowly. Clean up the faces with a hand plane, sandpaper on a block, and a square. Always works well enough for me. I use a 1/4" Viking blade from Lee Valley. I think the slowness part is key to solving your predicament.


Top
 Profile  
 
PostPosted: Wed Apr 20, 2011 8:26 pm 
Offline
Cocobolo
Cocobolo

Joined: Tue Jun 15, 2010 4:49 pm
Posts: 365
Focus: Build
Status: Amateur
I just use a 9" bandsaw with a 1/4" blade and cut across the line I've drawn. Then I use my tabletop belt sander to sand it all flat. Has worked for me flawlessly each time. The only thing is I cut it a few degrees less than I want it, because after sanding it the angle always increases a little.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 16 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 23 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com