***** Guitar Project Jigs, Tools & Techniques Online Resources Archives OLF Video Page Library of plans MP3 Library Inlay Class
Offical Luthiers Forum





And our community proudly sponsored by:

RC Tonewoods | Stewart MacDonald | LuthiersForum
TasmanianTonewoods | OLF | OLF MERCH
Luthier Suppliers | Pacific Coast Woods | ELEVATE
OLF X | Tasmanian Acoustic Tonewood | Luthiers Forum Store!
Luthiers Forum | OLF Facebook | AVAIL SPACE
OLF | Alaska Specialty Woods | A.Hix Tonewood
Duke of Pearl | Birkonium CNC | Space




Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Fri Nov 22, 2024 7:16 pm


Board index » Forum Archive

All times are UTC - 5 hours





Post new topic Reply to topic  Page 2 of 2
  [ 34 posts ]  Go to page Previous  1, 2
  Print view Previous topic | Next topic 
Author Message
FishtownMike
 Post subject:
PostPosted: Fri Dec 07, 2007 9:22 am 
Offline
Koa
Koa

Joined: Sat Aug 04, 2007 10:37 am
Posts: 590
Location: United States
First name: Michael
Last Name: Shaw
City: Phila
State: PA
Zip/Postal Code: 19125
Country: United States
Don't worry Todd. I didn't take it as anything. Mike

_________________
Guitars, guitars and more guitars.
Top
 Profile  
 
Arnt Rian
 Post subject:
PostPosted: Fri Dec 07, 2007 10:48 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri Aug 26, 2005 5:49 pm
Posts: 2915
Location: Norway
I think it is easier to adjust the side purfling miters if they are not attached to the bindings. However, if you cut your own wooden pruflings they may not like to bend sideways so much, and attaching them to the bindings may be the only way to make them behave.

_________________
Rian Gitar og Mandolin
Top
 Profile  
 
Ricardo
 Post subject:
PostPosted: Fri Dec 07, 2007 10:53 am 
Offline
Koa
Koa
User avatar

Joined: Wed Apr 18, 2007 6:46 am
Posts: 1012
Location: Issaquah, Washington USA
Todd, I took your suggestions.  I was easily able to separate the bwb from the wood binding. I applied the bwb and mitred the end graft much easier than I would have before.  I used a drop of CA every few inches - worked like a charm. Thanks

_________________
A higher purpose for wood.
Rich Smith
Issaquah, WA
Top
 Profile  
 
Blanchard
 Post subject:
PostPosted: Fri Dec 07, 2007 2:01 pm 
Offline
Cocobolo
Cocobolo

Joined: Fri Jun 15, 2007 12:14 am
Posts: 332
Location: United States

I have found that using a minimum amount of moisture and heat when bending bindings greatly reduces the amount of "wiggle" in the purflings. The only problem is that it's a lot slower !

Also, I have been using CA to glue purflings to bindings prior to bending for 14 years... no problems yet.

I glue the binding/purfling assembly to the guitar with Titebond.

Mark
Top
 Profile  
 
Tom Armstrong
 Post subject:
PostPosted: Sun Dec 09, 2007 9:33 am 
Great jig.....hope you dont mind if I copy it.
regards,
Tom Armstrong
Top
  
 
Alexandru Marian
 Post subject:
PostPosted: Sun Dec 09, 2007 9:49 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Thu Mar 22, 2007 10:59 pm
Posts: 2103
Location: Bucharest, Romania
Country: Romania
Focus: Build
Status: Professional
Really newb question coming up :D

which purfling are you guys adding prior to bending?  The one at the bottom, towards the sides?
Maybe the second, top purfling too?  Or that one is added after the main binding is glued?




_________________
Build log
Top
 Profile  
 
Greg N
 Post subject:
PostPosted: Sun Dec 09, 2007 10:50 am 
Offline
Walnut
Walnut

Joined: Sat Dec 01, 2007 5:11 am
Posts: 8
Location: United States
Subtle question.

I was taught that Purfling is an "inlaid" piece (the detail you traditionally see on violins and such) and Binding is any trim that creates a corner (you can see it on two faces like the neck shown above). Does this sound correct? Was it correct at one time but blurring as time goes by?

Greg N
Top
 Profile  
 
Greg N
 Post subject:
PostPosted: Sun Dec 09, 2007 10:53 am 
Offline
Walnut
Walnut

Joined: Sat Dec 01, 2007 5:11 am
Posts: 8
Location: United States
I wish I could edit my previous post.

I guess  you could consider the BWB above a Purfling and the white material (Curly maple?) the binding.  Or am I being too subtle?

Greg N
Top
 Profile  
 
Alexandru Marian
 Post subject:
PostPosted: Sun Dec 09, 2007 11:31 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Thu Mar 22, 2007 10:59 pm
Posts: 2103
Location: Bucharest, Romania
Country: Romania
Focus: Build
Status: Professional
Thanks. So, you have to inlay the back (or top) purfling *after* the binding+side purfling are in place. 

_________________
Build log
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 2 of 2
  [ 34 posts ]  Go to page Previous  1, 2

Board index » Forum Archive

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 45 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com