Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Dec 12, 2024 8:29 am


All times are UTC - 5 hours





Post new topic Reply to topic  [ 41 posts ]  Go to page 1, 2  Next
Author Message
 Post subject:
PostPosted: Mon Aug 13, 2007 3:19 am 
Offline
Old Growth Brazilian
Old Growth Brazilian

Joined: Tue Dec 28, 2004 1:56 am
Posts: 10707
Location: United States
Well I have done 6 tight cutaway tests now on a fairly tight 1" radius upper bout entry curve and a 1 1/4" return curve. I use .090-.085 thickness on all six tests using 2 scrap Curly Nara sides BobC was gracious enough to provide, Two orphaned Curly Cherry sides and 2 orphen quilted Sapele sides I had in shop. One of each without using SuperSoft and one with.

I used John Hows bending schedule. I soaked kraft paper for 2 min in distilled water, lightly spritzed the wood with distilled water. Wrapped the wood in the kraft paper. My sandwich was spring steel/wood/spring steel/ blanket/spring steel. I maintained constant but unforced upward tension on the sandwich behind the cutaway caul and bent all six sets at 310-315 taking only a few minutes to bend the cutaway.

Without SSII:

I cracked the Cherry in a later area of the entry bend along a curl change. Not but repairable This may have been operator error.

I had figure separation on the Sapele on the outside of the entry bend and inside of the return bend (outside of the bend but inside of the guitar)

I had figure separation only on the outside of the entry bend and a stress crack on the inside of the return bend on the untreated Narra.

Treated with SuperSoftII:
I wetted all three test pieces with SSII til they were fairly damp both sides. Placed kraft paper under and on top of the pieces and weighted them down with a piece of MDF and allowed 2 days to setup.

all three bent the cutaway like butter. This is good stuff in my opinion especially for tight bend on high figure woods.

I used John Hows bending schedule. I soaked kraft paper for 2 min in distilled water, lightly spritzed the wood with distilled water. Wrapped the wood in the kraft paper. My sandwich was spring steel/wood/spring steel/ blanket/spring steel. I maintained constant but unforced upward tension on the sandwich behind the cutaway caul and bent all six sets at 310-315 taking only a few minutes to bend the cutaway.


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 13, 2007 3:37 am 
Offline
Koa
Koa

Joined: Fri Sep 30, 2005 10:33 pm
Posts: 954
Location: United States
Just so I understand...you soak the sides in SS2 for 2 days prior to bending, then use the normal protocol? is this how others have used this product..interesting test, thanks a bunch!

Greg

_________________
Gwaltney Guitars


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 13, 2007 3:43 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Fri Nov 03, 2006 6:50 pm
Posts: 2711
Location: Victoria, BC
First name: John
Last Name: Abercrombie
Status: Amateur
Thanks, Michael-sounds like good stuff.
What was your source for SuperSoftII? (I'll be looking for somebody to ship to Canada).
And, is this a newer product (SuperSoft II)?

Thanks again

John





Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 13, 2007 3:43 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Mar 19, 2007 7:05 am
Posts: 9191
Location: United States
First name: Waddy
Last Name: Thomson
City: Charlotte
State: NC
Focus: Build
Status: Semi-pro
I think he just wets each side, and lets it dry for two days, while weighted to keep it flat.

_________________
Waddy

Photobucket Build Album Library

Sound Clips of most of my guitars


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 13, 2007 3:47 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Mon Dec 27, 2004 3:50 pm
Posts: 4662
Location: Napa, CA
Over the past 2 years, I've used the stuff on 6 sets now that included WF Bubinga, Quilted Sapele, Cherry, EIR and bindings that included maple, snakewood, BRW.

I spray SSII and allow it to dry overnight before bending. I also use craft paper but use less water. In six guitars I have also had no interference with gluing nor finishing.

Good stuff!

_________________
JJ
Napa, CA
http://www.DonohueGuitars.com


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 13, 2007 3:47 am 
Offline
Old Growth Brazilian
Old Growth Brazilian

Joined: Tue Dec 28, 2004 1:56 am
Posts: 10707
Location: United States
Yes


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 13, 2007 3:48 am 
Offline
Old Growth Brazilian
Old Growth Brazilian

Joined: Tue Dec 28, 2004 1:56 am
Posts: 10707
Location: United States
Wet once and allow to dry for 2 days


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 13, 2007 3:49 am 
Offline
Old Growth Brazilian
Old Growth Brazilian

Joined: Tue Dec 28, 2004 1:56 am
Posts: 10707
Location: United States
veneersuplies.com


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 13, 2007 3:58 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Mar 19, 2007 7:05 am
Posts: 9191
Location: United States
First name: Waddy
Last Name: Thomson
City: Charlotte
State: NC
Focus: Build
Status: Semi-pro
Also highlandwoodworking.com, but veneersupplies.com has a better price on gallons by $10.00 right now.

_________________
Waddy

Photobucket Build Album Library

Sound Clips of most of my guitars


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 13, 2007 4:04 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Fri Nov 03, 2006 6:50 pm
Posts: 2711
Location: Victoria, BC
First name: John
Last Name: Abercrombie
Status: Amateur
Thanks, guys.

John


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 13, 2007 4:30 am 
Offline
Old Growth Brazilian Rosewood
Old Growth Brazilian Rosewood
User avatar

Joined: Mon Dec 27, 2004 1:20 pm
Posts: 5915
Location: United States

That is great Michael. Thanks for the post.

Does this effect the elasticity of the sides once they have been bent?


_________________
Brock Poling
Columbus, Ohio
http://www.polingguitars.com


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 13, 2007 4:35 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Sat Jan 08, 2005 1:26 am
Posts: 2556
Location: United States
Brock, I've found no difference in spring back or any other elasticity issues. I've been using it for the last 12 guitars and won't ever bend another side without it.
Greg: for clarification: the sides never get soaked. Just wet down with a spray bottle. The two days is to let them dry. The SSII needs to be dry before heating or it will leave horrible stains. But you can still wet it with water once it is dry and won't have issues.


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 13, 2007 4:35 am 
Offline
Old Growth Brazilian
Old Growth Brazilian

Joined: Tue Dec 28, 2004 1:56 am
Posts: 10707
Location: United States
The are in no way floppy. All I have read states that the effects of the SSII lasts for about 4- 7 day. but even if it is permanent by the time you have your body assembled the sides would be so stiff I can't see it being an issue


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 13, 2007 4:37 am 
Offline
Old Growth Brazilian
Old Growth Brazilian

Joined: Tue Dec 28, 2004 1:56 am
Posts: 10707
Location: United States
I guess I should have also stated that I only treated the area from the center of the waist forward.


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 13, 2007 4:49 am 
Offline
Old Growth Brazilian
Old Growth Brazilian

Joined: Tue Dec 28, 2004 1:56 am
Posts: 10707
Location: United States
One the same note. one of the cherry sides I did spray the hole side with SSII just for kicks. As the temp got near 250% I saw the lower bout stat to sag. and then at 275 it just laid down over the form with out even pulling the bout caul around the the form at all. I knew right then and there that the stuff does work. Typically Cherry will droop a good bit at about 275% but I have never had one lay completely down on the form without pulling the call into place


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 13, 2007 5:06 am 
Offline
Old Growth Brazilian Rosewood
Old Growth Brazilian Rosewood
User avatar

Joined: Mon Dec 27, 2004 1:20 pm
Posts: 5915
Location: United States

Cool... just one more question.

Does it do anything to the color of the wood? .. for instance if you only treat one side and not the other, is there any color change?


_________________
Brock Poling
Columbus, Ohio
http://www.polingguitars.com


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 13, 2007 5:10 am 
Offline
Old Growth Brazilian
Old Growth Brazilian

Joined: Tue Dec 28, 2004 1:56 am
Posts: 10707
Location: United States
none that I could concern. I was worried about the same thing but once dry the treated area looked the same as untreated.


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 13, 2007 5:32 am 
Offline
Koa
Koa
User avatar

Joined: Wed Jan 31, 2007 7:17 am
Posts: 1383
Location: Canada
FWIW, I used a 50% solution of "veneer softner" I get from A&M here in Canada on the tight bits (only, water everywhere else) on my last curly maple cutaway (1" R with 1.25"R  horn) in a "bulbs only" fox bender. Just wet / wrap with tinfoil / sandwich / bend. Came out great! No waiting - no discolouration.

_________________
Dave
Milton, ON


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 13, 2007 1:03 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Thu Mar 01, 2007 3:15 pm
Posts: 2302
Location: Florida

Thanks for posting this! I'll definitely be looking to get some of this as I have a series of OM cutaways coming up next.


 


_________________
Reguards,

Ken H


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 13, 2007 1:07 pm 
Offline
Koa
Koa
User avatar

Joined: Sat Jul 01, 2006 5:55 am
Posts: 1392
Location: United States
First name: James
Last Name: Bolan
City: Nashville
State: Tennessee
Country: USA
Thanks Michael,I just ordered some.
                        James

_________________
James W Bolan
Nashville Tennessee


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 13, 2007 7:15 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Sun Dec 25, 2005 7:58 pm
Posts: 2946
Location: United States
Micheal thanks for the report, I'll have to try this stuff too.

[quote]As the temp got near 250%[/quote]

   If you want to make a degree symbol(?), hold down the alt key and press 0186.

   Thanks again for the heads up on the SSII

_________________
Billy Dean Thomas
Covina, CA

"Multi famam, conscientiam, pauci verentur."
(Many fear their reputation, few their conscience)


Top
 Profile  
 
 Post subject:
PostPosted: Tue Aug 14, 2007 3:34 am 
Offline
Koa
Koa
User avatar

Joined: Thu Feb 24, 2005 4:53 am
Posts: 1584
Location: PA, United States
Anyone tried Woodcraft's version called Pro-Glue? I have it, but haven't used it yet...
]


Top
 Profile  
 
 Post subject:
PostPosted: Tue Aug 14, 2007 3:51 am 
Offline
Old Growth Brazilian
Old Growth Brazilian

Joined: Tue Dec 28, 2004 1:56 am
Posts: 10707
Location: United States
What is the egrediance. The main ingredient in SSII is isoclycol


Top
 Profile  
 
 Post subject:
PostPosted: Tue Aug 14, 2007 8:09 am 
Offline
Koa
Koa
User avatar

Joined: Thu Feb 24, 2005 4:53 am
Posts: 1584
Location: PA, United States
Hi Michael,

Alcohol, glycerin, adhesive, fixative, and water. Glycerin would be the softener.


Top
 Profile  
 
 Post subject:
PostPosted: Tue Aug 14, 2007 8:56 am 
Offline
Koa
Koa

Joined: Mon Sep 04, 2006 10:55 pm
Posts: 698
Location: Australia
I just ordered a gallon from Veneer Supplies after all the glowing recommendations.

But the freight!!! OUCH. $75US for a $30 product.

I guess it's still inexpensive when you consider the the
price of timber and the resultant costs if we crack a set of exotic timber and have to get another set in from the States.

Thanks for the info gents.

Cheers

_________________

------------------------------------------------------
Bob Connor
Geelong, Australia


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 41 posts ]  Go to page 1, 2  Next

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 21 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com