Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Wed Dec 11, 2024 6:23 pm


All times are UTC - 5 hours





Post new topic Reply to topic  [ 23 posts ] 
Author Message
 Post subject:
PostPosted: Mon Aug 06, 2007 5:54 am 
Offline
Koa
Koa

Joined: Thu Dec 01, 2005 5:10 pm
Posts: 778
Location: Madison, WI
Is there a significant difference between Honduran mahogany and Sapele? Structurally?
Any alternative woods to Honduran to suggest? I'm looking for a large enough piece not to need to stack the heel block.
-j.

_________________
“If God dwells inside us like some people say, I sure hope He likes enchiladas, because that's what He's getting”
-jack handy


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 06, 2007 6:20 am 
Offline
Koa
Koa

Joined: Thu Nov 10, 2005 12:43 pm
Posts: 1031
Location: United States
Sapele works just fine. Most of our sponsors can supply you with blanks. Hibdon and Colonial come to mind, but othyers should have them as well.

Al


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 06, 2007 7:17 am 
Offline
Koa
Koa

Joined: Thu Dec 01, 2005 5:10 pm
Posts: 778
Location: Madison, WI
I intend to buy from a sponsor, but I wanted to see if anyone had any experience with them or had preferences before I purchased anything.

_________________
“If God dwells inside us like some people say, I sure hope He likes enchiladas, because that's what He's getting”
-jack handy


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 06, 2007 8:34 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Wed Jan 05, 2005 6:25 pm
Posts: 2749
Location: Netherlands
Sapele's stronger and stiffer (and usually a little heavier) than Honduran. On average. Khaya's the tricky one, and can be all over the map (some pieces perfectly good for necks, others, well, no way).

Honduran and Sapele are (in that order) my favourite necks woods. And the order is mostly because Honduran is nicer/easier to carve...


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 06, 2007 11:04 am 
Offline
Koa
Koa

Joined: Sun Feb 26, 2006 10:21 pm
Posts: 1055
Location: Australia
Ive found the opposite to Mattia with the wood Ive had in my workshop. I find the Sapele a little easier to work than the Honduras Mahogany.


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 06, 2007 1:42 pm 
Offline
Koa
Koa
User avatar

Joined: Thu Dec 01, 2005 3:05 pm
Posts: 503
Location: Portland, Oregon
I like Sapele a lot. It is a little stiffer, and heavier as Mattia mentioned(of course always speaking generally, there are always exceptions). I find Sapele is a little more brittle and can be a bit harder to work(but that would be expected)than Honduran Mahogany. I do think Sapele is a wonderful bargain though, and has an amazing look.

Just to stay perfectly in sync with Mattia. I also find Khaya to vary quite. I also find it can be a bit stringy as you carve and smooth a neck. Not such a big deal on say a solid body guitar, but gets old on necks.

Good luck!Rich


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 06, 2007 1:52 pm 
Offline
Koa
Koa

Joined: Wed Aug 24, 2005 11:13 am
Posts: 1398
Location: United States
You all might want to try good old cedro, aka Spanish cedar.   A favorite wood of Flamenco builders, a traditional neck wood for Martin in the old days...now coming back. Add a bit of graphite, and it's way wonderful.


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 06, 2007 2:30 pm 
Offline
Cocobolo
Cocobolo

Joined: Fri Mar 30, 2007 1:59 pm
Posts: 115
Location: United States
I've had a ton of Spanish Cedar stacked in the bottom of the pile for years.  The MC was very low (less that 7%) when it came in and it has never stopped sweating out resin.  Does this stop after it's under finish?


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 06, 2007 4:33 pm 
Offline
Koa
Koa

Joined: Sun Feb 26, 2006 10:21 pm
Posts: 1055
Location: Australia
Spanish cedar is great to work with and dont you just love that smell!


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 06, 2007 6:54 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Wed Jan 05, 2005 6:25 pm
Posts: 2749
Location: Netherlands
Rick: I've got a big pile of Cedro boards waiting to be used as bodies (electric), necks, some of it kerfed linings. Thing is, my local yards aren't importing any more of it, and it's about as expensive (and difficult to find) as good Honduran.


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 06, 2007 8:20 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Thu Jan 06, 2005 7:29 am
Posts: 3840
Location: England
Sapele as others have said is a perfectly good neck wood. My favourite at the moment though is cherry, again it's a little heavier than Honduran, but works nicely and finishes beautifully with no need to pore fill. My recent OM that I posted has it as a neck. I started using it as a neck wood for my lutes.

I also, as Rick said like cedrela, using it on classical necks, but it would be better reinforced for a SS. I too love it's ease of working and the smell of it when but not the aweful bitter taste if you get dust in your mouth, Urrggh!

John Kinnaird and others also like ash as a neck wood. I think this is one area that can have a great efect on things like sustain, but because Honduran has been the default wood, has lacked the experimentation.

Mattia, Cedrela is cheap as chips at Madinter and the quality of the last batch I got from them was amazing. In fact I think I'll order some more.

Colin

_________________
I don't believe in anything, I simply make use of a set of reasonable working hypotheses.


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 06, 2007 9:54 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri Aug 26, 2005 5:49 pm
Posts: 2915
Location: Norway
I have some nice ash from John K that I am sure will make a fine neck; beautiful curl too. I like to use ash for many general woodworking projects, and in things like long bows, sledge handles and so on. It is a great wood for this with tremendous strength in the long fibres but usually a bit on the heavy side, as is good old maple wich of course is another of the "old standard" neck woods.

_________________
Rian Gitar og Mandolin


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 06, 2007 9:55 pm 
Offline
Koa
Koa

Joined: Mon Sep 04, 2006 10:55 pm
Posts: 698
Location: Australia
And as time goes on we'll have to find more alternatives to Honduran Colin.

We can still get Fijian plantation mahogany here in Oz but it is variable in quality. The last plank I bought for necks ended up yielding around 20% due to worm holes.

I'm in the middle of a Tas Myrtle/Maple/Jarrah neck at present and the myrtle, like Cherry, is great to work with and also no pore filling.

African Mahogany, Sapele, Queensland Maple, Blackwood, Sassafras and Narra are the other alternatives that we can get hold of readily so let the experimentaion commence.

Cheers


_________________

------------------------------------------------------
Bob Connor
Geelong, Australia


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 06, 2007 9:58 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri Aug 26, 2005 5:49 pm
Posts: 2915
Location: Norway
...It seems the summer has done little to improve my spelling. When did you say that edit button was due back?

_________________
Rian Gitar og Mandolin


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 06, 2007 10:17 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Thu Jan 06, 2005 7:29 am
Posts: 3840
Location: England
Bob, the mahogany I get now is also plantation grown but in India and Sri Lanka, same as a lot of the EIR and it is of very good quality. I've probably got enough good mahogany to last out my building lifetime, both as neck wood and B&S sets but I still think that alternative neck woods are a good place to experiment.

Arnt as I think has been said before, your English spelling is a lot better than our Norwegian spelling would be!

Colin

_________________
I don't believe in anything, I simply make use of a set of reasonable working hypotheses.


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 06, 2007 10:25 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri Aug 26, 2005 5:49 pm
Posts: 2915
Location: Norway
Well that is a comfort I guess!

_________________
Rian Gitar og Mandolin


Top
 Profile  
 
 Post subject:
PostPosted: Mon Aug 06, 2007 10:59 pm 
Offline
Koa
Koa

Joined: Wed Jan 05, 2005 10:43 pm
Posts: 1124
Location: Australia
First name: Paul
Last Name: Burns
City: Forster
State: NSW
Zip/Postal Code: 2428
Country: Australia
Focus: Build
Status: Amateur
I'm building two with Narra necks right now. The Jury is still out until I get one finished. It works very much like Honduran and weighs about the same (might be a little more brittle), there's a fair bit of variation in density from piece to piece - the denser pieces tend to have nicer colour and some figure. Most of it rings like a bell. Gerard Gilet has been using it for necks for a few years and has been getting good results.

I hope it's good, I've got enough for 4 or five more necks, but at about $US10 per neck it's not much of a risk.


Top
 Profile  
 
 Post subject:
PostPosted: Tue Aug 07, 2007 1:37 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Wed Jan 05, 2005 6:25 pm
Posts: 2749
Location: Netherlands
Dammit, Colin, stop pointing out Madinter's website! I need to wait until everyone else who lives in the house is off on vacation, and time the delivery accordingly, so nobody notices the extra zoot creeping into the house.

Thanks for the reminder re: Cherry, though - my local-local (new discovery!) wood yard stocks exactly 12 species of hardwood, and Cherry is one of them. Have my first cherry neck build planned to commence soon, though.


Top
 Profile  
 
 Post subject:
PostPosted: Tue Aug 07, 2007 1:53 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Mar 19, 2007 7:05 am
Posts: 9191
Location: United States
First name: Waddy
Last Name: Thomson
City: Charlotte
State: NC
Focus: Build
Status: Semi-pro
Speaking of Ash, is anyone familiar with Black Ash?  I had never heard of it, but someone offered me some, and I wasn't sure how to respond.  I said yes, and I'm still not sure it will happen, but she said she has a friend that cuts a lot of it, and was sure he would be glad to let some go.

_________________
Waddy

Photobucket Build Album Library

Sound Clips of most of my guitars


Top
 Profile  
 
 Post subject:
PostPosted: Tue Aug 07, 2007 5:14 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri Nov 11, 2005 3:32 am
Posts: 2683
Location: Ithaca, New York, United States
Black ash: Fraxinus nigra. In some recent correspondence with a tonewood supplier about neck woods, he suggested black ash, which he called "northern swamp black ash". I was asking him if he had any black limba, which is another wood that's been used for necks and whose properties seem to lend themselves well to that purpose (I don't have personal experience with instruments with limba necks, but I'm soon going to be building one). He said he didn't have any, but that black ash has very similar properties, and that he recommended experimenting with it as a neck wood. He also suggested that it may be easier to carve and sand than white ash (Fraxinus americana).

So, to add to the list of suggested neck woods: black ash, limba, and let's not forget walnut.

I am refraining from naming the tonewood supplier I was referring to, since he isn't an OLF sponsor. PM me if you'd like to know.

_________________
Todd Rose
Ithaca, NY

https://www.dreamingrosesecobnb.com/todds-art-music

https://www.facebook.com/ToddRoseGuitars/


Top
 Profile  
 
 Post subject:
PostPosted: Tue Aug 07, 2007 7:27 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Sat Jun 17, 2006 3:48 am
Posts: 2094
[QUOTE=bob_connor] And as time goes on we'll have to find more alternatives to Honduran Colin.

We can still get Fijian plantation mahogany here in Oz but it is variable in quality. The last plank I bought for necks ended up yielding around 20% due to worm holes.

I'm in the middle of a Tas Myrtle/Maple/Jarrah neck at present and the myrtle, like Cherry, is great to work with and also no pore filling.

African Mahogany, Sapele, Queensland Maple, Blackwood, Sassafras and Narra are the other alternatives that we can get hold of readily so let the experimentaion commence.

Cheers

[/QUOTE]

Bob, I am working with some Oregon Myrtle at the moment. It's an absolutely wonderful wood to work with. Planing it is an enjoyable task, and seems incredibly similar to walnut. I have some chunks of greenwood cherry I'm waiting to air dry for a few necks.


Top
 Profile  
 
 Post subject:
PostPosted: Tue Aug 07, 2007 7:30 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Sat Jun 17, 2006 3:48 am
Posts: 2094
Forgot to add, I'm also working with African mahogany- seems a little more coarser than Honduras. Still nice stuff though.


Top
 Profile  
 
 Post subject:
PostPosted: Tue Aug 07, 2007 10:01 am 
Offline
Koa
Koa

Joined: Thu Dec 01, 2005 5:10 pm
Posts: 778
Location: Madison, WI
Excellent info. I will be using on a steel string, just to clarify.

-j.

_________________
“If God dwells inside us like some people say, I sure hope He likes enchiladas, because that's what He's getting”
-jack handy


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 23 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 30 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com