***** Guitar Project Jigs, Tools & Techniques Online Resources Archives OLF Video Page Library of plans MP3 Library Inlay Class
Offical Luthiers Forum





And our community proudly sponsored by:

RC Tonewoods | Stewart MacDonald | LuthiersForum
TasmanianTonewoods | OLF | OLF MERCH
Luthier Suppliers | Pacific Coast Woods | ELEVATE
OLF X | Tasmanian Acoustic Tonewood | Luthiers Forum Store!
Luthiers Forum | OLF Facebook | AVAIL SPACE
OLF | Alaska Specialty Woods | A.Hix Tonewood
Duke of Pearl | Birkonium CNC | Space




Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Fri Nov 22, 2024 2:56 am


Board index » Electric Guitar & Bass Construction

All times are UTC - 5 hours





Post new topic Reply to topic  Page 1 of 1
  [ 10 posts ] 
  Print view Previous topic | Next topic 
Author Message
old_picker
PostPosted: Tue Feb 27, 2018 5:46 pm 
Offline
Walnut
Walnut

Joined: Sun Mar 23, 2008 6:47 pm
Posts: 17
Haven't posted here in a cockatoo's age

About to finish another guitar in lacquer and again thinking on how to keep the finish out of the bridge and stop bar holes. I have tried tissue, thin scrunched plastic, Plasticine and just shot lacquer straight over them and cleaned up after.

Inevitably I will lose finish when pulling the fill or have it shatter when tapping in the bushings. Worst thing is time consuming lacquer repairs putting a barrier between the customers cash and my wallet.

Any one have a tip?
greatly appreciated and thanks in advance
Top
 Profile  
 
B. Howard
PostPosted: Wed Feb 28, 2018 8:40 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Mon Dec 27, 2010 9:06 pm
Posts: 2739
Location: Magnolia DE
First name: Brian
Last Name: Howard
City: Magnolia
State: Delaware
Zip/Postal Code: 19962
Country: United States
Focus: Repair
Status: Professional
I finish over them and press the bushings in hot. The heat will keep them from chipping the finish.

_________________
Brian

You never know what you are capable of until you actually try.

https://www.howardguitarsdelaware.com/


These users thanked the author B. Howard for the post (total 2): old_picker (Wed Feb 28, 2018 6:18 pm) • Pmaj7 (Wed Feb 28, 2018 11:11 am)
Top
 Profile  
 
dzsmith
PostPosted: Wed Feb 28, 2018 12:47 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri May 18, 2012 8:35 pm
Posts: 2660
Location: Austin, Texas
First name: Dan
Last Name: Smith
City: Round Rock
State: TX
Zip/Postal Code: 78681
Country: USA
Focus: Build
Status: Amateur
I install the bushings slightly below the body surface before finishing, and cover them with tape.
I use a Dremel to create a step for bushings that have a lip.

_________________
wah
Wah-wah-wah-wah
Wah


These users thanked the author dzsmith for the post: old_picker (Wed Feb 28, 2018 6:18 pm)
Top
 Profile  
 
old_picker
PostPosted: Wed Feb 28, 2018 6:21 pm 
Offline
Walnut
Walnut

Joined: Sun Mar 23, 2008 6:47 pm
Posts: 17
dzsmith wrote:
I use a Dremel to create a step for bushings that have a lip.


the step is done before finishing or after finishing?
Top
 Profile  
 
dzsmith
PostPosted: Wed Feb 28, 2018 9:21 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri May 18, 2012 8:35 pm
Posts: 2660
Location: Austin, Texas
First name: Dan
Last Name: Smith
City: Round Rock
State: TX
Zip/Postal Code: 78681
Country: USA
Focus: Build
Status: Amateur
old_picker wrote:
dzsmith wrote:
I use a Dremel to create a step for bushings that have a lip.


the step is done before finishing or after finishing?

Before finishing.


You do not have the required permissions to view the files attached to this post.

_________________
wah
Wah-wah-wah-wah
Wah


These users thanked the author dzsmith for the post: old_picker (Wed Feb 28, 2018 11:45 pm)
Top
 Profile  
 
old_picker
PostPosted: Wed Feb 28, 2018 11:47 pm 
Offline
Walnut
Walnut

Joined: Sun Mar 23, 2008 6:47 pm
Posts: 17
Love to know how you get a dremel to cut a nice even step like that - I was thinking on using a 19mm countersink bit. Currently masking up and about to start on shellac as pore fill. This one is in korina and the grain is very open which takes a lot to fill out. So I have a few days before I start laying down lacquer coats to get this right. I drove the stop bar studs just below the surface and I will tape them off as per your suggestion.

btw that looks like a very nicely built instrument and the burl is quite stunning [:Y:]


These users thanked the author old_picker for the post: dzsmith (Thu Mar 01, 2018 9:49 am)
Top
 Profile  
 
dzsmith
PostPosted: Thu Mar 01, 2018 9:48 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri May 18, 2012 8:35 pm
Posts: 2660
Location: Austin, Texas
First name: Dan
Last Name: Smith
City: Round Rock
State: TX
Zip/Postal Code: 78681
Country: USA
Focus: Build
Status: Amateur
I mounted the Dremel in a router base, and routed it out by hand.

_________________
wah
Wah-wah-wah-wah
Wah


These users thanked the author dzsmith for the post: old_picker (Thu Mar 01, 2018 5:03 pm)
Top
 Profile  
 
old_picker
PostPosted: Thu Mar 01, 2018 5:06 pm 
Offline
Walnut
Walnut

Joined: Sun Mar 23, 2008 6:47 pm
Posts: 17
ok good hands i reckon - i tend to be less trusting of getting a neat result
i will do it like that but mount a 16mm mdf on top with 2 x 14mm holes @74mm centers punched through as a bit of a guide
Top
 Profile  
 
fumblefinger
PostPosted: Thu Mar 01, 2018 11:02 pm 
Offline
Contributing Member
Contributing Member

Joined: Sun Jun 08, 2014 10:06 pm
Posts: 414
First name: Allan
Last Name: Bacon
State: Kansas
Country: USA
Focus: Repair
You might give these a try. A reverse spot face tool.
https://www.yardstore.com/drilling-and- ... se-cutters
Top
 Profile  
 
rlrhett
PostPosted: Fri Mar 02, 2018 10:34 am 
Offline
Koa
Koa
User avatar

Joined: Mon Nov 24, 2008 12:17 pm
Posts: 1168
City: Escondido
State: CA
Zip/Postal Code: 92029
Country: USA
Focus: Build
Status: Semi-pro
Keeping Finish out of body holes?....


Pants and a good respirator.


Sent from my iPhone using Tapatalk Pro


These users thanked the author rlrhett for the post (total 2): John Lewis (Sat Mar 03, 2018 3:49 pm) • fumblefinger (Sat Mar 03, 2018 12:29 am)
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 10 posts ] 

Board index » Electric Guitar & Bass Construction

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 25 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com