Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Fri Nov 22, 2024 10:28 pm


All times are UTC - 5 hours





Post new topic Reply to topic  [ 5 posts ] 
Author Message
PostPosted: Sat Feb 01, 2014 12:57 pm 
Offline
Cocobolo
Cocobolo

Joined: Thu Aug 16, 2012 1:47 pm
Posts: 122
First name: Mark
Last Name: Sweeney
City: South Ohio
State: Nova Scotia
Zip/Postal Code: B0W3E0
Country: Canada
Focus: Build
Status: Amateur
My latest build is buzzing like crazy when plugged in, so I assume I have a grounding issue. all cavities are shielded properly with copper foil tape, I've triple checked my wiring and all looks good. the only thing I can figure, is that the bridge is not properly grounded. I have a brass baseplate for my bridge that is painted black, I scraped some paint off around where the ground wire comes in, but wasn't able to solder the wire to it, and if it did stick, it wasnt lining up properly with the hole, and would break off very easily. so after a quick google search, I read that people were just running the wire through the cavity, and leaving some bare lead under the bridge, but no technically attaching it. I tried this, but it hums very bad, and I also seem to have volume issues.
Is there a better way?
What do you guys do?


Top
 Profile  
 
PostPosted: Sat Feb 01, 2014 1:13 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Fri Jan 15, 2010 3:34 pm
Posts: 2047
First name: Stuart
Last Name: Gort
Country: USA
Focus: Build
Status: Semi-pro
I drill and tap a hole in the base so my connections are always a sort of screw terminal type.

You could do this easily by getting the right size hole drilled and then hand tapping with a little bottoming tap. I can help you pick the drill and tap but you have to start with the right little screw and work back from there. Once you have the screw you want to use I can call out the right drill size for that tap.

_________________
I read Emerson on the can. A foolish consistency is the hobgoblin of little minds...true...but a consistent reading of Emerson has its uses nevertheless.

StuMusic


Top
 Profile  
 
PostPosted: Sat Feb 01, 2014 1:18 pm 
Offline
Contributing Member
Contributing Member

Joined: Mon Jul 11, 2011 12:43 am
Posts: 1326
Location: chicagoland, illinois
City: chicagoland
State: illinois
Country: usa
Focus: Build
Status: Amateur
if all else fails, you can disconnect most or all of the wires, leave the control cavity plate off, get some alligator clip test leads, and fool around with different wiring permutations (with the guitar plugged in to the amp) till you get an acceptable circuit...
if the output signal is weak, a good portion of it is probably being bled to ground.. i'd look at the volume and tone pot(s) connections


Top
 Profile  
 
PostPosted: Sat Feb 01, 2014 7:49 pm 
Offline
Cocobolo
Cocobolo

Joined: Thu Aug 16, 2012 1:47 pm
Posts: 122
First name: Mark
Last Name: Sweeney
City: South Ohio
State: Nova Scotia
Zip/Postal Code: B0W3E0
Country: Canada
Focus: Build
Status: Amateur
thanks guys, Got it fixed, I was confused about the wiring of the jack apparently..... a little embarrassed....


Top
 Profile  
 
PostPosted: Mon Feb 03, 2014 1:13 pm 
Offline
Contributing Member
Contributing Member

Joined: Fri Jun 22, 2012 11:12 am
Posts: 1170
First name: Rodger
Last Name: Knox
City: Baltimore
State: MD
Zip/Postal Code: 21234
Country: USA
Focus: Build
Status: Amateur
I was going to say check the jack, swapping the hot & ground will produce your symptoms. DAMHIKT.

_________________
A man hears what he wants to hear, and disreguards the rest. Paul Simon


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 5 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 44 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com