Waddy! Considering your link leads to "http://" I guess it's... technically... correct, but not very specific!
| Official Luthiers Forum! http://mowrystrings.luthiersforum.com/forum/ |
|
| Where is Lance’s shell cutting video? http://mowrystrings.luthiersforum.com/forum/viewtopic.php?f=10102&t=14734 |
Page 1 of 1 |
| Author: | Dennis Leahy [ Thu Nov 29, 2007 1:54 am ] |
| Post subject: | |
I have searched the forums including the archives, OLF Video Page, Sound Salon... Lance did a nice video showing his technique for cutting shell (abalone) strips. Does anyone know where that video can be found? Thanks, Dennis |
|
| Author: | WaddyThomson [ Thu Nov 29, 2007 2:00 am ] |
| Post subject: | |
Dennis, go to Sound Salon at the top of the page. The shell cutting stuff is there. |
|
| Author: | WaddyThomson [ Thu Nov 29, 2007 2:02 am ] |
| Post subject: | |
The videos are embedded in the inlay tutorials. |
|
| Author: | Dennis Leahy [ Thu Nov 29, 2007 2:03 am ] |
| Post subject: | |
Thanks, Waddy, but I'm not looking for the inlaying stuff right now, I'm looking for the video where Lance shows his jig and technique for making shell strips. Dennis |
|
| Author: | WaddyThomson [ Thu Nov 29, 2007 2:03 am ] |
| Post subject: | |
These may not be the ones you are thinking about, though. I just remembered them from a visit there. |
|
| Author: | WaddyThomson [ Thu Nov 29, 2007 2:10 am ] |
| Post subject: | |
Here is one thread that Lance started, but D.L.Huskey showed his little sawing setup for cutting shell. I found it by searching for "cutting abalone". There are some other threads there too. Try "cutting mop" or "cutting m.o.p." too. You might get some more hits. |
|
| Author: | Billy T [ Fri Nov 30, 2007 4:38 am ] |
| Post subject: | |
Waddy! Considering your link leads to "http://" I guess it's... technically... correct, but not very specific!
|
|
| Author: | LanceK [ Fri Nov 30, 2007 4:58 am ] |
| Post subject: | |
Here ya go Dennis! Sorry bout that 
Shell Cutting Jig PS, its 25 meg. |
|
| Author: | WaddyThomson [ Fri Nov 30, 2007 5:13 am ] |
| Post subject: | |
[QUOTE=Billy T]Waddy! Considering your link leads to "http://" I guess it's... technically... correct, but not very specific! [/QUOTE]OOPS!  Glad Lance came through! |
|
| Author: | Dennis Leahy [ Fri Nov 30, 2007 5:21 am ] |
| Post subject: | |
Thanks, Lance! Thanks for trying, Waddy! (I have been lost in cyberspace since I clicked that link.... )
Dennis |
|
| Author: | WaddyThomson [ Fri Nov 30, 2007 6:00 am ] |
| Post subject: | |
Welcome Back to OLF, Dennis. Some people here know stuff! 
|
|
| Author: | rich altieri [ Fri Nov 30, 2007 1:38 pm ] |
| Post subject: | |
How big is the cost advantage of cutting your own strips? |
|
| Author: | j.Brown [ Fri Nov 30, 2007 4:49 pm ] |
| Post subject: | |
Does anyone have video or pictorals on inlaying these strips into curved purfling? -j. |
|
| Author: | Billy T [ Sat Dec 01, 2007 7:06 pm ] |
| Post subject: | |
{Quote=Spidey]Thanks, Lance! Thanks for trying, Waddy! (I have been lost in cyberspace since I clicked that link.... ) [/quote]
Yup! Good to have you back, Dennis!! 
|
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|