Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Fri Nov 22, 2024 6:40 pm


All times are UTC - 5 hours





Post new topic Reply to topic  [ 6 posts ] 
Author Message
 Post subject: 1981 Vantage VS600
PostPosted: Sun May 31, 2015 1:29 pm 
Offline
Mahogany
Mahogany
User avatar

Joined: Sat Feb 21, 2015 4:36 pm
Posts: 76
Location: Buford, GA.
First name: Dean
Last Name: Miller
City: Buford
State: Georgia
Zip/Postal Code: 30518
Country: US
Focus: Build
Status: Amateur
Hi,

Would anyone happen to have a wiring diagram for a 1981 Vantage VS600 Geetar?

Thanks,

_________________
Dean


Top
 Profile  
 
 Post subject: Re: 1981 Vantage VS600
PostPosted: Tue Jun 02, 2015 5:39 am 
Offline
Contributing Member
Contributing Member

Joined: Wed Jun 25, 2014 3:26 am
Posts: 97
First name: Brian
Last Name: Wilson
Country: Scotland
Focus: Build
Status: Amateur
Depends. Seen those with 1 volume 1 tone a 3way switch and a toggle, right up to 2 vol 2 tone and 3 toggles. What's yours?


Top
 Profile  
 
 Post subject: Re: 1981 Vantage VS600
PostPosted: Tue Jun 02, 2015 6:03 am 
Offline
Cocobolo
Cocobolo

Joined: Fri Jul 01, 2011 9:17 am
Posts: 381
First name: Michael
State: AR
Country: USA
Focus: Build
Status: Amateur
http://www.dimarzio.com/sites/default/files/diagrams/2h1v1t_3w_all1dpdtonoffon.pdf - the one I think you're after. If not it's a good place for the other wiring diagrams for whatever you want to use the mini-switch for such as coil-splitter.

You may need to double check the color codes of the four wire HB's. They're not all the same.

http://www.seymourduncan.com/support/schematics/schematics.php?schematic=color_codes - a good chart.


Top
 Profile  
 
 Post subject: Re: 1981 Vantage VS600
PostPosted: Tue Jun 02, 2015 1:45 pm 
Offline
Mahogany
Mahogany
User avatar

Joined: Sat Feb 21, 2015 4:36 pm
Posts: 76
Location: Buford, GA.
First name: Dean
Last Name: Miller
City: Buford
State: Georgia
Zip/Postal Code: 30518
Country: US
Focus: Build
Status: Amateur
Yeah the guitar is going to be gutted. Everything is going to be replaced with new components. Pickups, Bridge, Pots, Switches, Wiring, Tuners, Knobs. And I am adding the Seymour Duncan Triple Shot HB Mounting Rings which add some really cool functionality.

The factory bridge is rusted and pitted, one pickup had already been replaced years ago, switches are bad, some of the tuners are not holding tune,... etc.. etc... etc...

So this is really a clean slate. I am wanting to add some cool functionality for my Brother-In-Law. First, like I said are the Triple Shots, then I have on hand two push pull pots, new on-on-on switches large and small to replace the originals... The Triple Shots, if you are not familiar with them, will turn each HB, or each side of a HB on/off as desired. One of the three way switches just turns the entire HB on/off which is okay too.

Maybe I am trying to add too much I dunno, I have regular pots to use as well. Maybe just use the Triple shots, 3-Way HB Selector, and use the other switch to put the HB's into series or parallel ?

_________________
Dean


Top
 Profile  
 
 Post subject: Re: 1981 Vantage VS600
PostPosted: Tue Jun 02, 2015 5:14 pm 
Offline
Cocobolo
Cocobolo

Joined: Fri Jul 01, 2011 9:17 am
Posts: 381
First name: Michael
State: AR
Country: USA
Focus: Build
Status: Amateur
AR15DCM wrote:
Yeah the guitar is going to be gutted. Everything is going to be replaced with new components. Pickups, Bridge, Pots, Switches, Wiring, Tuners, Knobs. And I am adding the Seymour Duncan Triple Shot HB Mounting Rings which add some really cool functionality.

The factory bridge is rusted and pitted, one pickup had already been replaced years ago, switches are bad, some of the tuners are not holding tune,... etc.. etc... etc...

So this is really a clean slate. I am wanting to add some cool functionality for my Brother-In-Law. First, like I said are the Triple Shots, then I have on hand two push pull pots, new on-on-on switches large and small to replace the originals... The Triple Shots, if you are not familiar with them, will turn each HB, or each side of a HB on/off as desired. One of the three way switches just turns the entire HB on/off which is okay too.

Maybe I am trying to add too much I dunno, I have regular pots to use as well. Maybe just use the Triple shots, 3-Way HB Selector, and use the other switch to put the HB's into series or parallel ?



Huh...cool. So I guess you really didn't have a question. Never mind and good luck with the project.


Top
 Profile  
 
 Post subject: Re: 1981 Vantage VS600
PostPosted: Tue Jun 02, 2015 7:18 pm 
Offline
Mahogany
Mahogany
User avatar

Joined: Sat Feb 21, 2015 4:36 pm
Posts: 76
Location: Buford, GA.
First name: Dean
Last Name: Miller
City: Buford
State: Georgia
Zip/Postal Code: 30518
Country: US
Focus: Build
Status: Amateur
No, I do have a question. Does anyone have the original wiring diagram for Vantage VS600 ? I want to understand how it was originally wired to learn about it and incorporate the original features.

_________________
Dean


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 6 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 52 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com