Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Sun Nov 24, 2024 12:59 pm


All times are UTC - 5 hours





Post new topic Reply to topic  [ 5 posts ] 
Author Message
PostPosted: Thu Sep 07, 2023 2:22 pm 
Offline
Walnut
Walnut

Joined: Sat Feb 01, 2020 12:37 pm
Posts: 8
I'm attempting to install a LSR roller nut into a Stratocaster neck and, though I've gotten the width correct and parallel, my depth is uneven. Pretty sure I don't want to be filing down the more shallow side and need to figure out how to fill the too-deep side. I'm struggling to Google for "guitar nut slot fill" because all Iget are how-tos related to the nut itself.

Any suggestions appreciated...


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
PostPosted: Thu Sep 07, 2023 2:57 pm 
Online
Contributing Member
Contributing Member
User avatar

Joined: Sun Mar 06, 2011 12:04 am
Posts: 5821
First name: Chris
Last Name: Pile
City: Wichita
State: Kansas
Country: Good old US of A
Focus: Repair
Status: Professional
Stop.
Use a router.

_________________
"Act your age, not your shoe size" - Prince


Top
 Profile  
 
PostPosted: Fri Sep 08, 2023 3:12 am 
Offline
Old Growth Brazilian Rosewood
Old Growth Brazilian Rosewood
User avatar

Joined: Fri Nov 02, 2007 9:49 am
Posts: 13386
Location: Ann Arbor, Michigan
First name: Hesh
Last Name: Breakstone
City: Ann Arbor
State: Michigan
Country: United States
Status: Professional
What Chris said AND fill should be the same material as the fret board with some attempt to make it invisible. The goal is zero gaps, full surface contact and no trace of a retrofit so maybe Chris consider a router to clean up the channel, matching wood fill, Final Cut with router and then install the nut.

You could clean up the channel with chisels and files but you need files made to fit that channel and most people don't have them.



These users thanked the author Hesh for the post: Chris Pile (Fri Sep 08, 2023 9:07 am)
Top
 Profile  
 
PostPosted: Fri Sep 08, 2023 9:07 am 
Online
Contributing Member
Contributing Member
User avatar

Joined: Sun Mar 06, 2011 12:04 am
Posts: 5821
First name: Chris
Last Name: Pile
City: Wichita
State: Kansas
Country: Good old US of A
Focus: Repair
Status: Professional
And good luck. Let us know how it turns out!

_________________
"Act your age, not your shoe size" - Prince


Top
 Profile  
 
PostPosted: Fri Sep 08, 2023 2:35 pm 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Fri Mar 17, 2017 8:42 pm
Posts: 400
First name: Pierre
Last Name: Castonguay
City: Québec, Qc
Country: Canada
Focus: Repair
Status: Professional
Hesh wrote:
What Chris said AND fill should be the same material as the fret board with some attempt to make it invisible. The goal is zero gaps, full surface contact and no trace of a retrofit so maybe Chris consider a router to clean up the channel, matching wood fill, Final Cut with router and then install the nut.

You could clean up the channel with chisels and files but you need files made to fit that channel and most people don't have them.

I have installed a couple of those and a router is definitely a must. I agree with Hesh on the course of action : route a bit further, fill with the same wood, and do a final pass over your fix.


Pierre
Guitares Torvisse

_________________
Pierre Castonguay


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 5 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 25 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com