| Official Luthiers Forum! http://mowrystrings.luthiersforum.com/forum/ |
|
| Mohawk Instrument Lacquer checking http://mowrystrings.luthiersforum.com/forum/viewtopic.php?f=10137&t=54469 |
Page 1 of 1 |
| Author: | jshelton [ Fri Oct 08, 2021 3:23 pm ] |
| Post subject: | Mohawk Instrument Lacquer checking |
I have two guitars we made in 2013 that have finish checking. I remember someone talking about repairing the checking but can't remember how it was done. Can one of you finish experts help me out? |
|
| Author: | Glen H [ Fri Oct 08, 2021 5:44 pm ] |
| Post subject: | Re: Mohawk Instrument Lacquer checking |
Some info here http://frets.com/FretsPages/Luthier/Technique/Finish/Lacquer/Amalgamator/amalgamator1.html |
|
| Author: | joshnothing [ Sun Oct 10, 2021 1:58 am ] |
| Post subject: | Re: Mohawk Instrument Lacquer checking |
jshelton wrote: I have two guitars we made in 2013 that have finish checking. I remember someone talking about repairing the checking but can't remember how it was done. Can one of you finish experts help me out? I’m no finish expert but I’ve just got through successfully repairing some checks in Mohawk lacquer this week. I used St. Frank’s advice in that frets.com link as a guide and had good results; widen the crack with a sharp knife, brush in Mohawk retarder, let dry, begin to brush in undiluted Mohawk lacquer, I do around four applications per day but you could probably do more. I stop as soon as I see sufficient build that I can cut it back level. Standard procedure for levelling - get close by scraping with a razor before block sanding. I have cut back and buffed successfully after seven days curing time , although as per nitro in general it buffs better the longer you wait. |
|
| Author: | Kbore [ Fri Jul 14, 2023 11:13 am ] |
| Post subject: | Re: Mohawk Instrument Lacquer checking |
jshelton wrote: I have two guitars we made in 2013 that have finish checking. I remember someone talking about repairing the checking but can't remember how it was done. Can one of you finish experts help me out? Would love a follow-up. Asking for help, getting replies then not following up is not good forum etiquette…. |
|
| Author: | Pmaj7 [ Fri Jul 14, 2023 5:03 pm ] |
| Post subject: | Re: Mohawk Instrument Lacquer checking |
Kbore wrote: Asking for help, getting replies then not following up is not good forum etiquette…. Guilty! I try to go back and catch up. Often so many great replies come in that I spend a lot of time thinking about them, re-reading and appreciating and I want to give thoughtful follow up that honors the advice. Sometimes I don't get back to it promptly and it falls off the radar... Pat |
|
| Author: | jshelton [ Sat Jul 15, 2023 3:11 pm ] |
| Post subject: | Re: Mohawk Instrument Lacquer checking |
Kbore wrote: jshelton wrote: I have two guitars we made in 2013 that have finish checking. I remember someone talking about repairing the checking but can't remember how it was done. Can one of you finish experts help me out? Would love a follow-up. Asking for help, getting replies then not following up is not good forum etiquette…. Apparently you didn't notice that I thanked the responders. I switched to Cardinal and have had no further problems. I hope that satisfies your worries about etiquette. I don't post on this site anymore since apparently the way I write sets people off. Why, I don't know (nor do I care). |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|