Official Luthiers Forum! • View topic

Board index » Electric Guitar & Bass Construction

All times are UTC - 5 hours

custom pickguard vendor

Page 1 of 1

[ 6 posts ]

Print view

Previous topic | Next topic

Author

Message

dberkowitz

Post subject: custom pickguard vendor

Posted: Thu Nov 30, 2017 10:36 am

Koa

Joined: Tue Jan 25, 2005 6:35 am
Posts: 671
Location: United States
Focus: Build
Status: Professional

Anyone work with a vendor they like for making custom pickguards? Someone to whom I can send a dxf file or similar? Suggestions?

Top

Ken McKay

Post subject: Re: custom pickguard vendor

Posted: Thu Nov 30, 2017 2:43 pm

Koa

Joined: Fri Jan 25, 2008 9:55 am
Posts: 982
Location: Traverse City Michigan

WD will do a good job.

Sent from my iPhone using Tapatalk

_________________
Ken

Top

dberkowitz

Post subject: Re: custom pickguard vendor

Posted: Thu Nov 30, 2017 3:11 pm

Koa

Joined: Tue Jan 25, 2005 6:35 am
Posts: 671
Location: United States
Focus: Build
Status: Professional

Ken McKay wrote:

WD will do a good job.

Ken, does WD do full custom pickguards, or only from pre-existing designs? I need someone to do a small run of pickguards for a guitar of my design. I'm not looking for a custom Tele or strat pick guard. Just want to be clear.

Top

Ken McKay

Post subject: Re: custom pickguard vendor

Posted: Thu Nov 30, 2017 4:15 pm

Koa

Joined: Fri Jan 25, 2008 9:55 am
Posts: 982
Location: Traverse City Michigan

Yes they do custom. Excellent workmanship.

Sent from my iPhone using Tapatalk

_________________
Ken

These users thanked the author Ken McKay for the post: dberkowitz (Thu Nov 30, 2017 4:47 pm)

Top

fumblefinger

Post subject: Re: custom pickguard vendor

Posted: Thu Nov 30, 2017 10:49 pm

Contributing Member

Joined: Sun Jun 08, 2014 10:06 pm
Posts: 414
First name: Allan
Last Name: Bacon
State: Kansas
Country: USA
Focus: Repair

Just a thought. I needed a custom TRC for a project. I laid it out on cad, printed a page off and taped it to a piece of plywood. Shaped the plywood to the paper and removed the paper. Screwed the pattern to a larger piece of plywood. Then did a rough cut on the pg material, and double face taped it on the plywood. I chucked up a 45 degree follower bit in the drill press. Then slowly ran the plywood pattern around the bit. It was slower than a router, but I had much better control and wasn't afraid of loosing a digit. It came out pretty nice so I made another in case the engraver hosed the first one. Don't know how much a custom would cost, but this was faster and easier.

You do not have the required permissions to view the files attached to this post.

Top

Ian Cunningham

Post subject: Re: custom pickguard vendor

Posted: Tue Jan 02, 2018 3:29 am

Koa

Joined: Tue Apr 27, 2010 9:07 pm
Posts: 512
City: Tucson
State: AZ
Country: USA
Focus: Build
Status: Amateur

Jat custom guitar parts. They also do knobs. Well worth a look.

These users thanked the author Ian Cunningham for the post: dberkowitz (Tue Jan 02, 2018 4:27 am)

Top

Page 1 of 1

[ 6 posts ]

Board index » Electric Guitar & Bass Construction

All times are UTC - 5 hours

Who is online

Users browsing this forum: No registered users and 34 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to: