***** Guitar Project Jigs, Tools & Techniques Online Resources Archives OLF Video Page Library of plans MP3 Library Inlay Class
Offical Luthiers Forum





And our community proudly sponsored by:

RC Tonewoods | Stewart MacDonald | LuthiersForum
TasmanianTonewoods | OLF | OLF MERCH
Luthier Suppliers | Pacific Coast Woods | ELEVATE
OLF X | Tasmanian Acoustic Tonewood | Luthiers Forum Store!
Luthiers Forum | OLF Facebook | AVAIL SPACE
OLF | Alaska Specialty Woods | A.Hix Tonewood
Duke of Pearl | Birkonium CNC | Space




Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Tue Nov 26, 2024 7:17 pm


Board index » Electric Guitar & Bass Construction

All times are UTC - 5 hours





Post new topic Reply to topic  Page 1 of 1
  [ 4 posts ] 
  Print view Previous topic | Next topic 
Author Message
shadahall
PostPosted: Tue Aug 20, 2013 5:46 pm 
Offline
Mahogany
Mahogany

Joined: Tue Jul 30, 2013 7:47 pm
Posts: 65
Location: Sacramento, CA, USA
First name: Shad
Last Name: Hall
Country: united states
Focus: Repair
Status: Amateur
hi,

so, as some of you know, i am doing a resto-mod on a strat knock off. i should also state that i've never owned an electric before, so this project is turning out to be a lot of fun in learning new things. today, i researched the differences of passive vs active pickups to determine if i should install a battery. i estimate from the following quote that it's highly dependant upon the pickups used, so i am considering the idea of just adding a battery to insure forward compatibility should i ever change/use pickups that could benefit from some extra juice.

the following bolded quotes caught my attention, especially regarding frequencies as i'm a live-sound tech, so i may have high standards.
Quote:
Passive Pickups: Passive pickups send a low output, raw signal to the amp that can only be affected by the volume and tone controls on the instrument itself. Passive pickups tend to lose the extremes of high and low frequencies, but still give a very even and punchy tone. This is because passive pickups tend to push out more midrange frequencies. While passive pickups might give players less dynamic control, their smooth sound is still very unique and desirable.

Active Pickups: Active pickups have preamps that are built into the pickup housing; so they can drive the signal to the amp themselves. This preamp must be powered by a source other than the amp, so active pickups require a separate battery to operate. This allows the pickup to send a higher output signal, producing a more complete, full-range sound than most passive pickup systems and giving players more control of instrument dynamics, projection and tone.

Quote:
Another benefit of active pickups is they often have much lower noise than passive pickups. This isn't such an issue with humbuckers, since their two coils are wired in such a way as to cancel much (though not, actually, all) of the 60-cycle hum. But single-coil pickups often have a lot of hum, even when well-shielded, while active pickups typically have very little.


regarding the 2 pictures on my blog documenting the project, http://lilbess.blogspot.com/2013/08/day-2.html, where would you suggest routing out a cavity and installing a batter and/or battery pack/door or whatever?

cheers,
shad
:)
Top
 Profile  
 
Chris Pile
PostPosted: Tue Aug 20, 2013 6:11 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sun Mar 06, 2011 12:04 am
Posts: 5823
First name: Chris
Last Name: Pile
City: Wichita
State: Kansas
Country: Good old US of A
Focus: Repair
Status: Professional
I used to just route a little deeper for a 9volt battery where it wouldn't interfere with the pots.

And it's called a solidbody....

_________________
"Act your age, not your shoe size" - Prince


These users thanked the author Chris Pile for the post: shadahall (Wed Aug 21, 2013 1:26 pm)
Top
 Profile  
 
shadahall
PostPosted: Tue Aug 20, 2013 6:30 pm 
Offline
Mahogany
Mahogany

Joined: Tue Jul 30, 2013 7:47 pm
Posts: 65
Location: Sacramento, CA, USA
First name: Shad
Last Name: Hall
Country: united states
Focus: Repair
Status: Amateur
Chris Pile wrote:
I used to just route a little deeper for a 9volt battery where it wouldn't interfere with the pots.

And it's called a solidbody....

hahahahahaha @ hardbody :)) i can't believe i said that ... i know it's a solidbody. i think lunacy is setting in. (@.0)

okay, will do @ your suggestion.

*still laughing*
Top
 Profile  
 
James T
PostPosted: Wed Aug 21, 2013 7:02 am 
Offline
Cocobolo
Cocobolo

Joined: Tue Dec 04, 2012 3:58 pm
Posts: 124
First name: James
Last Name: Tonguet
City: Duluth
State: Ga
Zip/Postal Code: 30096
Country: USA
Focus: Build
Status: Amateur
Most of my instruments are active , there typically is enough room in the cavity to fit the battery in , in this case you could rout a bit near the bridge end of the pickup cavity. The other thing to consider is room for a pre-amp ..


These users thanked the author James T for the post: shadahall (Wed Aug 21, 2013 1:26 pm)
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 4 posts ] 

Board index » Electric Guitar & Bass Construction

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 25 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com