| Official Luthiers Forum! http://mowrystrings.luthiersforum.com/forum/ |
|
| The Beast http://mowrystrings.luthiersforum.com/forum/viewtopic.php?f=10123&t=36400 |
Page 1 of 1 |
| Author: | An Lao Shi [ Sun May 06, 2012 4:57 am ] |
| Post subject: | The Beast |
I call this guitar "The Beast" because it has three humbucking pickups--my first three-pickup guitar. Each pickup can be turned on and off, offering a variety of sound choices. The top wood is maple. The back is made-up of ash on the outer sides, strips of amargo, and then two pieces of maple. The neck is maple with a rosewood fingerboard. There is a master volume control. The bridge is made by Wilkinson.   Questions and comments welcomed. |
|
| Author: | Chris Pile [ Sun May 06, 2012 8:18 am ] |
| Post subject: | Re: The Beast |
Clean design, good basic execution. A musical tool without the gingerbread. I LOVE IT! (I don't find it beastly at all) |
|
| Author: | Steve Davis [ Sun May 06, 2012 10:16 am ] |
| Post subject: | Re: The Beast |
clean simple and good looking I like it |
|
| Author: | Robbie_McD [ Sun May 06, 2012 10:25 am ] |
| Post subject: | Re: The Beast |
Very cool design, love it! |
|
| Author: | alan stassforth [ Sun May 06, 2012 10:33 am ] |
| Post subject: | Re: The Beast |
Very nice and clean. I like seeing non figured woods used on gits. I like figured wood too! Does it have a headstock? |
|
| Author: | jimmysux [ Sun May 06, 2012 10:59 am ] |
| Post subject: | Re: The Beast |
Nice work, good color coordination, clean build. I like it! |
|
| Author: | muskr@ [ Sun May 06, 2012 2:12 pm ] |
| Post subject: | Re: The Beast |
Very elegant in it's simplicity. Good job! ![[clap]](./images/smilies/smiley32.gif "adulations")
|
|
| Author: | Steve Davis [ Sun May 06, 2012 2:27 pm ] |
| Post subject: | Re: The Beast |
just looked at her again.. is that pot vol/tone push pull? |
|
| Author: | An Lao Shi [ Sun May 06, 2012 6:20 pm ] |
| Post subject: | Re: The Beast |
Thank you for your comments. I did take a few photos of the headstock, but they didn't turn out very well. I'll try to take another photo of it today. I'm a little embarrassed about the headstock because I should have spaced the tuners farther apart. I didn't notice this until I drilled the holes. The volume pot isn't push/pull. but that's a great idea. I have only recently learned how useful a tone control can be. Many of my guitars only have a volume control. By the way, I don't know if it is allowed to post a link to another website. I checked OLF to learn if it was and couldn't find anything either way. I documented this build on another website. I'll post the link here with apologies to the moderator if it's not allowed. http://www.offsetguitars.com/forums/vie ... =8&t=36653 Edited to add a photo of the headstock. You can see how the tuners begin a little too high on the headstock. The strings do not foul one another, however. The headstock cap is cocobolo. 
|
|
| Author: | Mike Baker [ Fri May 11, 2012 5:14 pm ] |
| Post subject: | Re: The Beast |
Nice! I like the design as well. Very clean execution, too. As for the headstock, I think it looks great. As far as the distance between tuners goes, as long as the strings do not hit the sides of the other tuners' posts(which they don't), spacing is up to the builder, IMHO. They don't look any more crowded than you might find on a six in line headstock(less, actually). Nothing to be embarrassed about, IMHO. Lovely work. |
|
| Author: | An Lao Shi [ Sun May 13, 2012 5:15 am ] |
| Post subject: | Re: The Beast |
Mike, thank you for the kind comments. |
|
| Author: | alan stassforth [ Sun May 13, 2012 12:22 pm ] |
| Post subject: | Re: The Beast |
Nice headstock. I like the way your tuners are scrunched closer together! Maybe you've started something there. |
|
| Author: | An Lao Shi [ Mon May 14, 2012 6:51 am ] |
| Post subject: | Re: The Beast |
Thank you, Alan. |
|
| Author: | Corky Long [ Mon May 14, 2012 8:03 am ] |
| Post subject: | Re: The Beast |
I agree with the other posts. i think the spacing of the tuners works very well - relative to the truss rod cover, I think the proportion gives it a very balanced feel, while not being totally conventional. Like. |
|
| Author: | Lincoln Goertzen [ Tue May 15, 2012 2:53 pm ] |
| Post subject: | Re: The Beast |
Me, too. I like the slick, clean job you've done. If someone challenges you on the headstock design, tell them it's for accommodating behind the nut bends. ![[:Y:]](./images/smilies/smiley20.gif "Thumbs Up")
|
|
| Author: | An Lao Shi [ Wed May 16, 2012 6:33 pm ] |
| Post subject: | Re: The Beast |
Thank you, Corky and Lincoln. If I remember correctly, I moved the tuners up to avoid the area I routed to access the truss rod adjustment. I have since stopped routing so far up the headstock. Thanks again to everyone who has responded and left comments. They're very much appreciated. |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|