| Official Luthiers Forum! http://mowrystrings.luthiersforum.com/forum/ |
|
| Favourite bits/mills and suppliers http://mowrystrings.luthiersforum.com/forum/viewtopic.php?f=10106&t=24989 |
Page 1 of 1 |
| Author: | Mattia Valente [ Thu Dec 10, 2009 3:26 pm ] |
| Post subject: | Favourite bits/mills and suppliers |
Well, the title says it all. Fess up! What are your favourite sources, and most used bits for various tasks? |
|
| Author: | Tim McKnight [ Thu Dec 10, 2009 5:01 pm ] |
| Post subject: | Re: Favourite bits/mills and suppliers |
Drill Bit City Onsrud Robb Jack Precise Bits South Eastern Carbide Just found the last source a few weeks ago and I am very impressed with their quality and sharpness of their V and straight 2 flute bits. Drill Bity City has great prices on 10 packs of carbide small fractional bits. Robb Jack has one of the largest selections of micro bits but the are not cheap. |
|
| Author: | BobK [ Fri Dec 11, 2009 12:19 pm ] |
| Post subject: | Re: Favourite bits/mills and suppliers |
Cutting Edge Technologies and Precise bits. I'll have to take a look at Tim's suggestions. |
|
| Author: | Bob Garrish [ Sat Dec 12, 2009 2:53 am ] |
| Post subject: | Re: Favourite bits/mills and suppliers |
Standard end mills are from OSG Specialized cutters from Micro100, Ridiculous, or American Carbide Micro cutters from Precisebits |
|
| Author: | Mattia Valente [ Sat Dec 12, 2009 4:30 pm ] |
| Post subject: | Re: Favourite bits/mills and suppliers |
Thanks for the links, plenty of good stuff there. I was also curious about what sized bits people like for specific applications. My hunch is a 1/2" ball nose stub will do a lot of the work, slightly longer reach for things like acoustic guitar necks, and a variety of bits from precisebits (and the endmills I have from CET already) for inlay and fret slots, and a few straight sqaure endmills for machining MDF and Phenolic for molds. I'm also having a look at the Amana Tool round bit Nelson linked to. Does anyone use 'normal' carbide tipped router bits for much? |
|
| Author: | Bob Garrish [ Sun Dec 13, 2009 2:57 pm ] |
| Post subject: | Re: Favourite bits/mills and suppliers |
Mattia Valente wrote: Does anyone use 'normal' carbide tipped router bits for much? Don't bother: they're more expensive and lower quality than solid carbide cutters. The only case in which I'd use a brazed router bit is if I was routing some sort of profile (like moulding) or when I need a roundover cutter. |
|
| Author: | Stuart Gort [ Sat Mar 13, 2010 2:08 am ] |
| Post subject: | Re: Favourite bits/mills and suppliers |
Most everything from tiny mills, four flute mills, ball and bull nose endmills, taps and drills from McMaster-Carr because they almost always arrive the next day and they have virtually everything except the odd thing. They carry decent or better quality. Counter-rotating matched sets from Onsrud. Top notch quality on everthing they do. Never cheap. Custom made tiny stuff from Cutting Edge Technologies. - For surfacing operations I always use a four flute bull or a four flute ball mill 1/2" to 3/4". A router turns way faster than my mill though so four flutes works better for me. - For drilling wood I always use a sharp endmill. I peck at the hole and dwell at the bottom for a few secs...if it's a drilling op. Or I might interpolate a hole if I can but I never drill wood with actual drills when I want an accurate hole. - For face milling I use a bull nose cutter (rounded corner) or an indexing face mill or a shell mill....but they all have rounded edges. - For contoured edges I use a ball and step down outside the contour until a depth equalling half the tool diameter is reached. Then I can use a bigger mill and take bigger bites after that without ripping. |
|
| Author: | Jim Watts [ Sat Mar 13, 2010 3:16 pm ] |
| Post subject: | Re: Favourite bits/mills and suppliers |
Robb Jack Precise bits and for any one cutting Aluminum you should check out Data Flute |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|