The other WTB thread got so long I didn't want to move it over, so I thought it would be better to start a new one.
Wow... what a great first wave... Just think... 9 more days of this.
| Official Luthiers Forum! http://mowrystrings.luthiersforum.com/forum/ |
|
| New WTB Thread http://mowrystrings.luthiersforum.com/forum/viewtopic.php?f=10102&t=14079 |
Page 1 of 2 |
| Author: | Brock Poling [ Mon Oct 15, 2007 12:10 pm ] |
| Post subject: | |
The other WTB thread got so long I didn't want to move it over, so I thought it would be better to start a new one. Wow... what a great first wave... Just think... 9 more days of this.
|
|
| Author: | Brock Poling [ Mon Oct 15, 2007 12:11 pm ] |
| Post subject: | |
I will go first. I am on the hunt for a set of Mac Ebony sides. If they are thin that is ok. I would prefer them to be book matched though. No need for 5A figure or anything. Just something decent without any flaws. |
|
| Author: | L. Presnall [ Mon Oct 15, 2007 12:32 pm ] |
| Post subject: | |
I need a bloodwood bridge blank... |
|
| Author: | MaxBishop [ Mon Oct 15, 2007 12:33 pm ] |
| Post subject: | |
I'd like to get some of that u Beaut Hard Shellac. Max Bishop Brighton, Michigan |
|
| Author: | outstrung [ Mon Oct 15, 2007 12:51 pm ] |
| Post subject: | |
I am looking for a fine grained Red Spruce top for an archtop. Thanks. |
|
| Author: | WaddyThomson [ Mon Oct 15, 2007 2:01 pm ] |
| Post subject: | |
I could use a Euro Spruce top or two. Preferably German or Italian. |
|
| Author: | rlabbe [ Mon Oct 15, 2007 2:02 pm ] |
| Post subject: | |
Since I hate making jigs, how about a vacuum press for gluing braces. |
|
| Author: | James Ringelspaugh [ Mon Oct 15, 2007 2:21 pm ] |
| Post subject: | |
I'd like some sinker redwood... |
|
| Author: | peterm [ Mon Oct 15, 2007 2:36 pm ] |
| Post subject: | |
I need a couple of LS Redwood tops. thanks |
|
| Author: | PDeWitt [ Mon Oct 15, 2007 2:39 pm ] |
| Post subject: | |
Inexpensive side bending iron to use for my first guitar (need to keep cost down). Thanks |
|
| Author: | Marc Lupien [ Mon Oct 15, 2007 2:41 pm ] |
| Post subject: | |
A couple of BRW sets below 250$ ??? I might be dreaming though! Thank's M |
|
| Author: | Cocephus [ Mon Oct 15, 2007 11:02 pm ] |
| Post subject: | |
A nut slotting file? Coe |
|
| Author: | TonyKarol [ Mon Oct 15, 2007 11:37 pm ] |
| Post subject: | |
Hesh .. the good blanks I have can be nicely bookmatch glued up to get the 1.75 you need - been done before here and it looks great !!! A 12 inch long blank will get you two matching bridges .... Lemme know if you are still interested ???? |
|
| Author: | Bruce Dickey [ Mon Oct 15, 2007 11:46 pm ] |
| Post subject: | |
A set of Ziricote Sides like LetsEatPaste's sets, I missed.
|
|
| Author: | rlabbe [ Tue Oct 16, 2007 12:08 am ] |
| Post subject: | |
Port orford cedar is used for bracing by some classical builders, such as Ruck and Oberg. I've been looking for some, but the hardwood dealers around here don't carry it. So, Bob and others, if your offcuts from processing tops creates wood good enough for bracing, I'll relieve you of it! |
|
| Author: | Bobc [ Tue Oct 16, 2007 12:24 am ] |
| Post subject: | |
Roger let me check. I may have some pieces. |
|
| Author: | Dave Rickard [ Tue Oct 16, 2007 12:43 am ] |
| Post subject: | |
Orphan Leopard wood sides |
|
| Author: | Dennis Leahy [ Tue Oct 16, 2007 4:05 am ] |
| Post subject: | |
I want to trade my pile of ivory for something - like a nice back and side set. There was recently a guy selling legal ivory nuts and saddles on Ebay, for a fixed price of $20 (if I remember correctly) which would have made my dozen pieces worth about $240.) Currently, I see an Ebay ad at $12/ea, which means my dozen is worth about $144. I'm willing to trade quite a bit lower than that value - you might be surprised. Even a really nice parlor sized set of __________. Dennis |
|
| Author: | RobE [ Tue Oct 16, 2007 7:21 am ] |
| Post subject: | |
I'm looking for some Bubinga or some nice Sapele. Any planes or tools are also appreciated. And some clamps too. |
|
| Author: | Burton LeGeyt [ Tue Oct 16, 2007 7:48 am ] |
| Post subject: | |
Hey Rob, I have some really nice Sapele on my page, with rosette and headstock blanks too. Let me know if you want better pics. Burton |
|
| Author: | Bob Long [ Tue Oct 16, 2007 8:10 am ] |
| Post subject: | |
Stew Mac Headband Magnifier Maybe someone has one of these they don't use, or something similar. long |
|
| Author: | joe white(old) [ Wed Oct 17, 2007 3:09 pm ] |
| Post subject: | |
I am looking for a maple back. at least 15 x 19.5 and 0.175 thick. |
|
| Author: | GregH [ Wed Oct 17, 2007 6:45 pm ] |
| Post subject: | |
Clamps - cam clamps, spring clamps, K clamps Tuning Machines - Individual slothead steel string double action truss rods Greg Heather Fort Worth, TX |
|
| Author: | Bobc [ Wed Oct 17, 2007 11:38 pm ] |
| Post subject: | |
German spruce is being listed in a few minutes. 
|
|
| Page 1 of 2 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|