Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Dec 12, 2024 11:05 am


All times are UTC - 5 hours





Post new topic Reply to topic  [ 6 posts ] 
Author Message
 Post subject:
PostPosted: Mon Aug 06, 2007 1:32 am 
Offline
Cocobolo
Cocobolo

Joined: Sat Jul 30, 2005 1:35 am
Posts: 228
Location: Australia
I have been meaning to put this up for while. I found the process of laying the purfling a bit tricky and wondered whether there was an alternative approach. I had been messing around with a homemade vacuum and thought that I might be able to form the rosette grouping of purfling veneers in the round.

The process entailed wrapping the veneers, polycarbonazte sheet, vinyl vacuum sheet around a pipe and applying the vacuum for about an hour. The formed rosette purfling was then sliced using the fret slotting saw to produce 0.080"/2mm slices.



regards

Tim


Top
 Profile  
 
 Post subject:
PostPosted: Tue Aug 07, 2007 1:32 am 
Offline
Cocobolo
Cocobolo

Joined: Sat Jul 30, 2005 1:35 am
Posts: 228
Location: Australia
I had an opportunity to take a couple of close up images. I will put up a few images of my vacuum form tomorrow





Top
 Profile  
 
 Post subject:
PostPosted: Tue Aug 07, 2007 1:46 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Wed Feb 01, 2006 3:25 am
Posts: 3788
Location: Russellville, Arkansas
Tim that worked very nicely.

Look forward to the pics of the vac form.

I'm stuck on individual lines from Martin.

This is intriguing however.

Thanks for sharing.

Question: How did you saw them? TIA

_________________
http://www.dickeyguitars.com


Top
 Profile  
 
 Post subject:
PostPosted: Tue Aug 07, 2007 1:47 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Sat Jan 08, 2005 1:26 am
Posts: 2556
Location: United States
Tim, what do you slice them with? I've had some bad luck using a bandsaw on cylindrical stuff like that.


Top
 Profile  
 
 Post subject:
PostPosted: Tue Aug 07, 2007 1:58 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Mar 19, 2007 7:05 am
Posts: 9191
Location: United States
First name: Waddy
Last Name: Thomson
City: Charlotte
State: NC
Focus: Build
Status: Semi-pro

[QUOTE=Pwoolson]Tim, what do you slice them with? I've had some bad luck using a bandsaw on cylindrical stuff like that. [/QUOTE]

I believe he said he uses a fret slotting saw blade.

_________________
Waddy

Photobucket Build Album Library

Sound Clips of most of my guitars


Top
 Profile  
 
 Post subject:
PostPosted: Tue Aug 07, 2007 2:02 am 
Offline
Cocobolo
Cocobolo

Joined: Sat Jul 30, 2005 1:35 am
Posts: 228
Location: Australia
Thanks Waddy.

That is correct however I should qualify it by saying that I tape up the lamination end to complete the circle and then place them in a cradle just above the fret slotting table saw blade and revolve the form to slice the rosette laminations. I will make sure I post a few pictures tomorrow.

Tim


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 6 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 22 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com