| Official Luthiers Forum! http://mowrystrings.luthiersforum.com/forum/ |
|
| Bracing for quilted maple http://mowrystrings.luthiersforum.com/forum/viewtopic.php?f=10101&t=55076 |
Page 1 of 1 |
| Author: | nathanpeirson [ Tue Jun 14, 2022 10:25 am ] |
| Post subject: | Bracing for quilted maple |
Hey folks, I just picked up a quilted maple back and sides from people liquidating their inventory. The sides are pre-bent and the back pre-braced. The bracing is much thicker than I have seen on other guitars (I will post a photo later). Is it normal to increase bracing mass for quilted maple? Sent from my iPhone using Tapatalk  
|
|
| Author: | meddlingfool [ Tue Jun 14, 2022 10:27 am ] |
| Post subject: | Re: Bracing for quilted maple |
I don’t… |
|
| Author: | Mike Collins [ Fri Jun 17, 2022 4:53 pm ] |
| Post subject: | Re: Bracing for quilted maple |
thats a martin style bracing plane down the # 3 & 4 braces. How thick is the back? Mike |
|
| Author: | nathanpeirson [ Tue Jul 05, 2022 1:42 pm ] |
| Post subject: | Bracing for quilted maple |
Sorry for the long delay. I was on vacation in Kings Canyon...beautiful country...marvelous trees. The thickness of the back is 0.110. The spruce top is also0.110. Not sure what kind of spruce it is but I'll add a picture. 
|
|
| Author: | meddlingfool [ Tue Jul 05, 2022 2:23 pm ] |
| Post subject: | Re: Bracing for quilted maple |
Pretty thick for a back, pretty standard for a top… |
|
| Author: | nathanpeirson [ Tue Jul 05, 2022 6:00 pm ] |
| Post subject: | Re: Bracing for quilted maple |
meddlingfool wrote: Pretty thick for a back, pretty standard for a top… What thickness do you recommend for the back and sides? Sent from my iPhone using Tapatalk |
|
| Author: | meddlingfool [ Tue Jul 05, 2022 7:57 pm ] |
| Post subject: | Re: Bracing for quilted maple |
I do most of my backs at .090”, and most sides .075”-.085”… |
|
| Author: | SnowManSnow [ Wed Jul 06, 2022 8:49 am ] |
| Post subject: | Re: Bracing for quilted maple |
You could play baseball w that back brace on the bottom:) Sent from my iPhone using Tapatalk |
|
| Author: | Clay S. [ Wed Jul 06, 2022 9:10 am ] |
| Post subject: | Re: Bracing for quilted maple |
The quilted maple back being a little thicker than commonly seen with other species doesn't bother me - it is a lighter weight wood, not particularly stiff and sometimes will warp in strange ways if made too thin. I agree with Mike Collins - the lower back braces should be thinned enough to add some flexibility to allow the back to cope with humidity changes. |
|
| Author: | Alan Carruth [ Wed Jul 06, 2022 3:01 pm ] |
| Post subject: | Re: Bracing for quilted maple |
Backs often work best when the two upper braces are tall and narrow and the two lower ones are low and wide. It's almost as if you simply started with them more or less the same and stood the upper ones on edge and laid the lower ones out flat. |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|