| Official Luthiers Forum! http://mowrystrings.luthiersforum.com/forum/ |
|
| What is going on is this photo http://mowrystrings.luthiersforum.com/forum/viewtopic.php?f=10101&t=54752 |
Page 1 of 1 |
| Author: | Slim [ Sun Feb 06, 2022 12:36 am ] |
| Post subject: | What is going on is this photo |
I’m not familiar with all the different jigs out being used so this one in the pic is new to me. What is going on in in this pic with this router jig is this some sort of thickness jig? |
|
| Author: | Mark Mc [ Sun Feb 06, 2022 12:52 am ] |
| Post subject: | Re: What is going on is this photo |
It looks like a thicknessing jig. I assume that the round black things are suction cups to hold the piece down? |
|
| Author: | ballbanjos [ Sun Feb 06, 2022 7:18 am ] |
| Post subject: | Re: What is going on is this photo |
I wonder if it is used to notch out the center reinforcement strip (not shown in this photo) for back braces or something like that? Dave |
|
| Author: | SteveSmith [ Sun Feb 06, 2022 7:32 am ] |
| Post subject: | Re: What is going on is this photo |
The round black things look like balls or rollers to hold down the plate so it can be thicknessed accurately. |
|
| Author: | Slim [ Sun Feb 06, 2022 7:35 am ] |
| Post subject: | Re: What is going on is this photo |
SteveSmith wrote: The round black things look like balls or rollers to hold down the plate so it can be thicknessed accurately. I think it might be marbles and most likely it has another set on the opposite but we can see it from the angle. |
|
| Author: | doncaparker [ Sun Feb 06, 2022 8:16 am ] |
| Post subject: | Re: What is going on is this photo |
I’m pretty sure it is a thicknessing jig. The round holes are for some method of pushing the plate down flat against the base, although I’m not sure what method is being used in the photo. I guess very large steel balls would do a good job. It wouldn’t be a center strip routing jig (at least not as shown), because the movement of the router allowed by the jig is perpendicular to the center strip line. |
|
| Author: | ThomLuth [ Mon Feb 07, 2022 12:12 am ] |
| Post subject: | Re: What is going on is this photo |
doncaparker wrote: It wouldn’t be a center strip routing jig (at least not as shown), because the movement of the router allowed by the jig is perpendicular to the center strip line. As Dave said, although there is no center strip reinforcement shown, it might be for routing the slot for the back braces. That was my first thought too. In that case, one would want the jig to allow perpendicular movement. The jig looks interesting, but to me, cutting a slot, or space for the back brace with a router jig seems like a lot of work, as opposed to just using a small razor saw. Tom |
|
| Author: | Slim [ Mon Feb 07, 2022 12:34 pm ] |
| Post subject: | Re: What is going on is this photo |
My first thought was it is for bringing down the thickness. It looks a lot like a those slab planing sleds guys use with the router. |
|
| Author: | SnowManSnow [ Mon Feb 07, 2022 5:20 pm ] |
| Post subject: | Re: What is going on is this photo |
I also say thickness jig I bet the round things are bearings that are level w the jig for the router plate to slide along on Sent from my iPhone using Tapatalk |
|
| Author: | Victor Seal [ Mon Feb 07, 2022 6:06 pm ] |
| Post subject: | Re: What is going on is this photo |
Removing braces???? |
|
| Author: | stumblin [ Tue Feb 08, 2022 8:55 am ] |
| Post subject: | Re: What is going on is this photo |
Found it! Thicknessing jig. Also discovered that a right click on the mouse over the photo gives an option to search for google images. https://luth.org/books/american-lutheri ... anthology/ |
|
| Author: | Clay S. [ Tue Feb 08, 2022 10:45 am ] |
| Post subject: | Re: What is going on is this photo |
stumblin wrote: Found it! Thicknessing jig. Also discovered that a right click on the mouse over the photo gives an option to search for google images. https://luth.org/books/american-lutheri ... anthology/ So that thing has balls with a magnetic attraction. It would certainly offer a cheaper alternative to a thickness sander as mentioned in the lead-in to the article. I think I would add a skirt like some CNCs have and a dust port for a vacuum cleaner. |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|