***** Guitar Project Jigs, Tools & Techniques Online Resources Archives OLF Video Page Library of plans MP3 Library Inlay Class
Offical Luthiers Forum





And our community proudly sponsored by:

RC Tonewoods | Stewart MacDonald | LuthiersForum
TasmanianTonewoods | OLF | OLF MERCH
Luthier Suppliers | Pacific Coast Woods | ELEVATE
OLF X | Tasmanian Acoustic Tonewood | Luthiers Forum Store!
Luthiers Forum | OLF Facebook | AVAIL SPACE
OLF | Alaska Specialty Woods | A.Hix Tonewood
Duke of Pearl | Birkonium CNC | Space




Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Sat Mar 01, 2025 11:11 am


Board index » Luthiers Forum Rooms » Guitar Building Forum

All times are UTC - 5 hours


Forum rules


Be nice, no cussin and enjoy!




Post new topic Reply to topic  Page 1 of 1
  [ 11 posts ] 
  Print view Previous topic | Next topic 
Author Message
SnowManSnow
PostPosted: Tue Jul 03, 2018 5:21 pm 
Offline
Koa
Koa

Joined: Fri Feb 24, 2017 8:43 am
Posts: 1707
I’m in the midst of an 000 build that I’m REALLY enjoying! This guitar though has a rounder top at the upper bout than the others I’ve built.
(The area above my reference holes where the neck will sit).
Do I just go about flattening the neck area with a sanding block?
Why am I afraid of this right now?
Image

And one of the pretty wenge back for fun
Image


Sent from my iPhone using Tapatalk Pro
Top
 Profile  
 
jac68984
PostPosted: Tue Jul 03, 2018 5:59 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri May 14, 2010 11:43 am
Posts: 668
First name: Aaron
Last Name: Craig
City: Kansas City
State: Missouri
Focus: Build
Status: Semi-pro
SnowManSnow wrote:
Do I just go about flattening the neck area with a sanding block?

Yes, to answer your question. But don’t get carried away. That’s really not all that round. Don’t fall into the trap of believing that where the neck meets the body the sides must be perfectly flat the width of the heal. Sure it makes things easier, but it doesn’t always look good with a given body shape, smaller bodied guitars in particular. As long as you relieve the insides of the heel cheeks, leaving only a bit over an eighth to a quarter inch or so of the outside heal to contact the sides of the guitar, you can achieve a flawless fit with a few strokes of sandpaper even on a very curvy upper bout.

Sent from my iPhone using Tapatalk Pro




Sent from my iPhone using Tapatalk Pro

_________________
Aaron Craig
Top
 Profile  
 
SnowManSnow
PostPosted: Tue Jul 03, 2018 6:12 pm 
Offline
Koa
Koa

Joined: Fri Feb 24, 2017 8:43 am
Posts: 1707
So if it isn’t flat then how do the cheeks make a good make up with the body?


Sent from my iPhone using Tapatalk Pro
Top
 Profile  
 
SnowManSnow
PostPosted: Tue Jul 03, 2018 6:13 pm 
Offline
Koa
Koa

Joined: Fri Feb 24, 2017 8:43 am
Posts: 1707
Image
Not a lot of flat area at all there


Sent from my iPhone using Tapatalk Pro
Top
 Profile  
 
Freeman
PostPosted: Tue Jul 03, 2018 6:24 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Thu Nov 04, 2010 1:46 pm
Posts: 2164
First name: Freeman
Last Name: Keller
Focus: Build
Status: Amateur
Cut the cheeks back next to the tenon with a chisel so just the outside edge (maybe a 1/8) contacts the body. Makes flossing much easier

Image
Top
 Profile  
 
SnowManSnow
PostPosted: Tue Jul 03, 2018 6:55 pm 
Offline
Koa
Koa

Joined: Fri Feb 24, 2017 8:43 am
Posts: 1707
Freeman wrote:
Cut the cheeks back next to the tenon with a chisel so just the outside edge (maybe a 1/8) contacts the body. Makes flossing much easier

Image

Yea sir I do.
I guess I’ve only really built OM Guitars until now. I always cut it back so that onlybthe outside of the cheek touches. That said an OM is pretty dang flat up there so I haven’t done this process before


Sent from my iPhone using Tapatalk Pro
Top
 Profile  
 
jac68984
PostPosted: Tue Jul 03, 2018 8:46 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri May 14, 2010 11:43 am
Posts: 668
First name: Aaron
Last Name: Craig
City: Kansas City
State: Missouri
Focus: Build
Status: Semi-pro
SnowManSnow wrote:
Freeman wrote:
Cut the cheeks back next to the tenon with a chisel so just the outside edge (maybe a 1/8) contacts the body. Makes flossing much easier

Image

Yea sir I do.
I guess I’ve only really built OM Guitars until now. I always cut it back so that onlybthe outside of the cheek touches. That said an OM is pretty dang flat up there so I haven’t done this process before


Sent from my iPhone using Tapatalk Pro


Same process then. You may just need to pare down a bit further than you are used to. And you may need to adjust the location of the body join fret a touch. Curvy shoulders mean that if the center of the join fret lines up with the body, the fret ends will be slightly above the body line (stated differently, the heel cheeks may need to extend (towards the bridge) slightly past the body join fret).


Sent from my iPhone using Tapatalk Pro

_________________
Aaron Craig
Top
 Profile  
 
SnowManSnow
PostPosted: Tue Jul 03, 2018 9:28 pm 
Offline
Koa
Koa

Joined: Fri Feb 24, 2017 8:43 am
Posts: 1707
jac68984 wrote:
SnowManSnow wrote:
Freeman wrote:
Cut the cheeks back next to the tenon with a chisel so just the outside edge (maybe a 1/8) contacts the body. Makes flossing much easier

Image

Yea sir I do.
I guess I’ve only really built OM Guitars until now. I always cut it back so that onlybthe outside of the cheek touches. That said an OM is pretty dang flat up there so I haven’t done this process before


Sent from my iPhone using Tapatalk Pro


Same process then. You may just need to pare down a bit further than you are used to. And you may need to adjust the location of the body join fret a touch. Curvy shoulders mean that if the center of the join fret lines up with the body, the fret ends will be slightly above the body line (stated differently, the heel cheeks may need to extend (towards the bridge) slightly past the body join fret).


Sent from my iPhone using Tapatalk Pro

Is this just so that it doesn’t look funny with a strait line against the curve?


Sent from my iPhone using Tapatalk Pro
Top
 Profile  
 
Freeman
PostPosted: Tue Jul 03, 2018 9:33 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Thu Nov 04, 2010 1:46 pm
Posts: 2164
First name: Freeman
Last Name: Keller
Focus: Build
Status: Amateur
Someone told me that they made the OM shape by pushing the 12th fret body join down to the 14ths, just basically flattened the upper bout. Most 12 fret and small body and classical guitars have curved upper bouts. Even so called "sloped shoulder" dreads. I love small bodied guitars, they are round and curvy.
Top
 Profile  
 
jac68984
PostPosted: Tue Jul 03, 2018 10:00 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri May 14, 2010 11:43 am
Posts: 668
First name: Aaron
Last Name: Craig
City: Kansas City
State: Missouri
Focus: Build
Status: Semi-pro
[/quote]
Is this just so that it doesn’t look funny with a strait line against the curve?


Sent from my iPhone using Tapatalk Pro[/quote]



That’s one reason. The other is that if you have used the top of the guitar at the head block centerline as your reference point for measuring and laying out braces and the bridge patch, failing to account for the slope and placing the fret ends at the widest point even with the body lines will throw off your saddle location slightly. Not a big problem if you have a wide bridge plate and haven’t already/don’t drill bridge location holes. But something to be aware of nonetheless.

I have no idea why my text is showing up this way. Lol. Technology...

Sent from my iPhone using Tapatalk Pro

_________________
Aaron Craig


Last edited by jac68984 on Tue Jul 03, 2018 11:04 pm, edited 1 time in total.

Top
 Profile  
 
SnowManSnow
PostPosted: Tue Jul 03, 2018 10:22 pm 
Offline
Koa
Koa

Joined: Fri Feb 24, 2017 8:43 am
Posts: 1707
Ok I’ll proceed as is then:)


Sent from my iPhone using Tapatalk Pro
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 11 posts ] 

Board index » Luthiers Forum Rooms » Guitar Building Forum

All times are UTC - 5 hours


Who is online

Users browsing this forum: Peter J and 48 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com