| Official Luthiers Forum! http://mowrystrings.luthiersforum.com/forum/ |
|
| Fret saw blades http://mowrystrings.luthiersforum.com/forum/viewtopic.php?f=10101&t=50191 |
Page 1 of 1 |
| Author: | BradHall [ Tue Jan 16, 2018 12:59 am ] |
| Post subject: | Fret saw blades |
Does anyone have an alternative source for 6" .023 or .025 circular saw blades? The $115+ StewMac blade seems excessive. I know it's a speciality blade and I generally try to support Lutherie suppliers. Also, do you send them out for sharpening, do it yourself, or dispose of used blades? On average how may fretboards do you get before the blade is dull? |
|
| Author: | Barry Daniels [ Tue Jan 16, 2018 2:59 pm ] |
| Post subject: | Re: Fret saw blades |
I sharpen mine with a file. Pretty easy if you know how. |
|
| Author: | edstrummer [ Tue Jan 16, 2018 3:33 pm ] |
| Post subject: | Re: Fret saw blades |
We used to sell similar blades at MSC Industrial. Probably McMaster too. Sent from my iPhone using Tapatalk |
|
| Author: | Joe Beaver [ Fri Jan 19, 2018 1:49 pm ] |
| Post subject: | Re: Fret saw blades |
I use the stewmac blade also. After about a dozen fretboards and a fair amount of kerfed lining making, I just sent it out for sharpening. Haven't got it back yet but I hope it is better than new when I do. |
|
| Author: | meddlingfool [ Fri Jan 19, 2018 2:56 pm ] |
| Post subject: | Re: Fret saw blades |
If you buy the LMI power slotting system once, it's a 200$ investment for everything it comes with. Subsequent replacement blades are only 57$. I did send one out to be sharpened, but they just cut new teeth in the old blade and it came back a different diameter. Which made it useless. |
|
| Author: | klooker [ Fri Jan 19, 2018 3:26 pm ] |
| Post subject: | Re: Fret saw blades |
How about the LMI blade & a set of CMT stabilizers? https://www.amazon.com/CMT-299-102-00-B ... B000P4NTRW |
|
| Author: | meddlingfool [ Fri Jan 19, 2018 5:27 pm ] |
| Post subject: | Re: Fret saw blades |
Maybe you'd get away with it. The LMI ones are 5.5", leaving ~ 1/4" blade exposure. I'd be worried about flop with the amount of blade exposed by 5" stiffeners... |
|
| Author: | klooker [ Fri Jan 19, 2018 11:04 pm ] |
| Post subject: | Re: Fret saw blades |
meddlingfool wrote: Maybe you'd get away with it. The LMI ones are 5.5", leaving ~ 1/4" blade exposure. I'd be worried about flop with the amount of blade exposed by 5" stiffeners... You very well may be right. Why else would LMI offer a solution that costs over 4x as much 
|
|
| Author: | rlrhett [ Sat Jan 20, 2018 12:31 am ] |
| Post subject: | Re: Fret saw blades |
For several years I used a “standard” 5” stiffener on 6” LMI blade and never noticed loose slots. .5” of exposed blade is not a crazy amount of exposure. YMMV Sent from my iPhone using Tapatalk |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|